I’m not sure what year it. You couldn’t really tell by the headlights or tail lights. But one doesn’t often see one of these in this condition too often.
One of a kind.
Back of the Bun!!
The interior was set up like a tour bus.
What I can tell you is that the big dog is resting what appears to be a Chevy Dually pick up truck bed. According to the sign it’s powered by a 5700 6.0 Vortech Chevy engine.
You are going to like this pics from Red Stripe Adventure’s blog. The lowered Lincoln in stealth black and you have to agree that Hudson looks great – in spite of the WWII aircraft theme.
Thanks for reading.
So I’ve gotten the new electrical connection installed on the switch. I now need to cut off the old switch and strip the wires.
Ya know it’s hard to take a video while you a squeezed under a car on jack-stands!!!
In this video you can see the striped wires.
Installing the bracket was easy enough except that it wasn’t formed properly and had to be bent. Keep in mind this is not ‘harden’ steel and too much bending will weaken it and when the reverse lever comes back will just push the bracket backward and not allow the button to be depressed enough to make contact and complete the circuit and turn the backup lights on.
Here it is all installed.
Here it is with the car in the reverse position. You can see the button depressed.
Here is a video shot.
And the intended results:
Now I’d love to tell you that all was well, however remember the bolt and the Sharpie mark I made on it so that I could gauge how far to screw it back in?
Well I was still pretty happy with the progress and I took the car off the jack-stand and started her up and backed out of the garage. That went well, but there didn’t seem to be a first gear once I decided to pull the car forward, nor second gear. She isn’t going to move.
So I’ve got the car out of the garage and right at the edge of the drive on the driver’s side. I have to get under the car and tighten that bold a few more turns. I end up laying partially on the drive way, partially on the rocks (we don’t have grass in your yards here..we have small, gather in you pants when you are laying on them, sharp rocks) and partially on one of your shrubs. Ok, lets not forget the glowing hot Hooker header pipes..yeah…just back out of the garage…no worries the hair on my arm will grow back. Any way, I tighten it just enough to get the car to go into second gear and pull it back into garage.
It had to go back up on the jack-stands for more adjustments, and I had to the switch off once to make adjustments to the bracket. But success was achieved!!!!!
The wait for the 2013 SRT Viper has only been about two years–since sales of the previous model ceased–but for fans of the venomous vanguard of American speed, it’s been a long one. The wait is drawing to a close now, and as we get closer, we get more of what to expect. Today, it’s the new Viper’s logo, dubbed “Stryker.”
Designed by Vince Galante, a Chrysler designer and Viper owner, the logo aims to capture the “sinister look and ‘evil grin’ of the original,” according to DriveSRT.
Previous logos were named Sneaky Pete and Fangs. Stryker follows in the theme with a stylized viper’s head, though the newest is the meanest-looking yet. As these sketches reveal, it’s born of the snake itself, but with a healthy dose of artistic interpretation.
While we don’t really think the badge has much to do with the car itself–they could have put a cupcake on the nose of the last Viper and it still would have been one of the meanest things on the road–the new direction fits our eyes well. Galante also notes that the new logo has some lines that reflect those of the car, too. What do you see?
As the Washington D.C. auto show took place, President Obama decided to make a visit. Truly impressed with the American muscle & sports cars. Though he checked out many new models and the likes of the controversial most iconic American sports car, Chevy Corvette(photo above), it seemed like the new Ford MustangShelby GT500 Super Snake; or simply Shelby GT500; is what really grabbed his attention by stating, “This is sick”.
I’ll be giving away two (2) National Motor Museum Mint die-cast (metal) Ford licensed replicas.
1934 V8 Deluxe Roadster (image is of the card that comes with the car)
1932 V8 Convertible Sedan (Image is of the card that comes with the car)
Want to know how to win?
Grab my feed/subscribe or follow The Average Guy’s Car Restoration, Mods and Racing (https://www.average-guys-car-restoration-mods-racing.com/ or www.timsweet.wordpress.com) and stay tuned for details.
Whenever I can I like post up a plea for someone doing a restoration that may need some assistance. The Sarasota County Lodge #45 needs assistance with restoring a 1953 patrol car. This car is a ’53 Chevy Bel Air 150.
Here are some details:
1953 Chevy Bel Air 150
The Sarasota County Lodge #45 of the Fraternal Order of Police is spearheading a project that will involve the restoration of an antique patrol car. The vehicle will match one that was actually used by the sheriff’s office since the office first purchased patrol cars in 1953. Once the restoration is complete, the vehicle will be donated to the Sarasota County Sheriff’s Office for various public uses.
By reviewing photographs in “From Shield to Star,” a book by retired Sgt. Bob Snell that documents the history of the department, several vehicles were identified by make and model. The first fleet of four vehicles consisted of 1953 Chevrolet Bel Air 150s. The project is being coordinated by FOP #45 Vice-President Kevin Lynch, who is a retired SSO lieutenant. Lynch has overseen the restoration of several emergency vehicles including two fire trucks and a Cadillac ambulance that he currently owns.
Tax-deductible contributions to this project can be sent to The Community Foundation of Sarasota County, P. O. Box 49587, Sarasota, FL 34230-6587, marked for the antique patrol car project.
The FOP is also looking for in-kind services and donations such as labor and supplies needed for the project, and possibly the vehicle itself. Storage space will also be needed for the vehicle as well as initial transportation to Sarasota. Questions can be sent to FOP Lodge #45 at P.O. Box 1488, Englewood, FL 34295-1488 or e-mailed to Lynch at floridafop45@yahoo.com. You may also visit the Lodge #45 website at foplodge45.com.
It’s been a while since I’ve provided an update on the restoration of the 1975 fuel injectedVW bug that I’m project managing for a former workmate. So I thought I’d post of some details andsome pics.
The car is called a “Standard” – that doesn’t mean a manual shift (although it is a manual 3 speed), that means the most stripped down, no optioned, VW you could purchase. I’m talking interior door panels with a thin covering of fake leather over (almost as thin) cardboard. Rubber floor coverings (I wouldn’t even call them mats!!!), a headliner, cloth seats were the total of trim in side. There was no upholstery covering the rest of the interior – just painted metal. It did have an AM radio – which was replaced it a JVC.
Not much to the door panel.
Headliner and sun visors are about the only other upholstery, the rest is painted red like you see here.
In fact importation of these striped down models was halted shortly after about 100 here shipped to the US in 1975. This is one of the 100 allowed in. Pretty cool story.
This particular car belongs to June Yang and she purchased the car, brand new, while attending college in Iowa. The car lived in Iowa it’s entire life (until now) and it show’s signs of every winter too. The car had been stored for years and suffers from a severe case of rust and by all accounts shouldn’t able to sit up-right on four tires.
But like many folks, who love their V-dubs, June has a lot of memories tied to the rusted fenders, college, and other life milestones. So when she moved to Tucson, Az she thought of bring the Bug with her. She was advised that the car was not safe to drive down the driveway much less the block and certainly not 1/2 way across country!!! And that was an
understatement!!!!!
I met June when she came to work at the same establishment where I labored. I’m not a closet car guy and a visit to my office at that time it was pretty clear. Eventually she asked about having the car fixed and her desire to have it join her in Az was discussed and although I had no idea the exact condition. I helped arrange transportation to Tucson.
The goal was to get it here to some place that could get the car running (it wouldn’t start and brakes hadn’t been serviced in some time). In run condition, the thought was we could then running it around (save a few $$) to the various places I had planned to do the work. Unfortunately even running it wasn’t going to be safe enough to drive. See here<<<<>>>>
The transport had one bump when the driver’s truck died en route. The company immediately arranged for a local company to pick it up and finish the trip. I believe June called them every hour for updates. Eventually, the car showed up at my favorite auto repair shop and Tim Sisk gave me a call to come look the car over.
These pictures don’t nearly capture the condition this car, frankly I was taken back as well and I grew up driving a 1930-ish Ford stripped down pick-up that served as an alternate tractor on my grandfather farm, in upstate New York – no floor boards and the like. This VW was nearly eaten alive by oxidation.
Rust 1
Rust 2
And here's a little side view.
See the highlighted area? It's not attached. It should be. It holds the body to the frame!!
So are you saying WHAAAATTT???? Pretty much the standard response… but don’t fret….there’s a plan!!!
One of my regular readers, Bill, posted the following question in response to the piece I wrote on Chevy engines. Bill asked…
“No 454 V8 in 1971? I guess that motor came later. ..”
That get me to thinking so I did a little more research. The references I’m use are “Ultimate AmericanV-8 Engine Data Book” by Peter Sessler; “Standard catalog of American Cars” by John Gunnel and “110 years of the American Auto” by James Flammang and Auto Editors of Consumer Guide. I try not to get too much from the Internet at large.
Interestingly enough the 454 is briefly mentioned in the Ultimate American V-8 Engine Data Book, but there aren’t many details. That reference shows that the 454 was available in 1971 as a 4V producing 365 horse power. It doesn’t show under any model just as a general option for Chevy’s. I’m assuming it was just a 400 block with a different bore and stroke.
The 454 was developed by 1970. It’s bore was 4.251 in and had a 4 inch stroke (where as the 400 had 4.251 in bore and a 3.75 stroke). There were other version in 1970 and 1971, designated as the LS5. This version of the 454 was used in the 1970 and beyond in Corvette for one instance and was used in Chevelle.
Interesting that it isn’t referred to in the mentioned references for 1971 year.
Hold the presses!!!!!
It appears that in the reference “Standard catalog of American Cars” by John Gunnel that the 454 was left out off the comprehensive listing of engines for 1971. However, the 454 was use in the SS version of the Monte Carlo – 1,919 were produced. For the Chevelle 80,000 were sold with the SS badge of those only 19,992 were with the 454.
1917 Chevelle SS 454
1971 Monte Carlo SS 454
And in this reference I found the answer to a question I’ve had for some time. About 5 years agoing I was at a car show and ended up talking to a guy with a 1971 Nova SS. It had a 454 as the power plant between the shock towers. However there were 7,015 Nova SS packages sold, none had the 454 as the option.
If you read any of my pieces on Engines, you’ll know that I enjoy learning all I can about the various makers’ details on their features. I thought that I might start a series that took a year by year approach to what the US automaker build and used in the cars they produced.
So here is the engine line up for the 1971 Chevys.
Of course Chevy had the V8’s in 1971, not yet strangled by smog control, as well as 6 cylinders and 4 cylinders.
All of the 6’s were inline (often referred to as straight 6 – for the pistons all being in a straight line configuration) these were 250 cubic inch displacements – (very similar to the Ford 250, with the exception of the Blue upping the compression to 9.1:1 vs Chevy’s 8.5:1). These were cast iron with hp running about 145 with hydraulic lifter, and normally topped with a Rochester one barrel carb. Any car that had a 6 in it had this engine and it was an option with most any Chevy model.
1971 Chev Inline Six (this one is in a Chevy Nova)
Next up is the 4 cylinder used exclusively in the Vega (remember those?). They were inline 4’s with Over head Cams, aluminum block (not iron) and managed to displace 140 cubic inches. The compression ratio was less than they 6 at 8.0:1 with hydraulic lifters and a one barrel carb.
Vega Four Cylinder
There were 3 basic V8 that year the 350, 400 and the 307.
The 350 cid was cast iron with overhead valves and compression ratio of 8.5:1 with an hp of 245 hp when it was topped with a 2 barrel Rochester carb. These were widely used in the Biscayne, Bel Air, Impala, and Monte Carlo.
The 400 was cast iron as well with matching stats. However due to the larger bore (4.125 vs the 4.00 for the 350) and longer stroke (3.75 inches compare to the 350’s 3.48) it was able to push the hp’s up to 255 (umm..seems like a lot of work for 5 hps) when it was topped with the same 2 barrel carb.
The 307 rounds this out with its cast iron block and over head valves, it to had the compression ratio of 8.5:1 but with a smaller bore and shorter stroke (3.875 and 3.5 inch)it bu down roughly 200 hp. The 307 was used in Chevelle, Malibu, Nova and the Camaro.
aunik_aronno
