There has been a lot of parking garage incidents lately but I think this one takes the cake. This isn’t some guy losing control on the nearby road and landing IN the parking garage. Not this time. This time the driver apparently went through the concrete wall of the third story of the parking garage in Lugano, Switzerland, and fell all the way down upon some parked mopeds and a tree. The 24-year old driver was only injured slightly after flying off of the third floor. You can say that this brand new 5.0 suffered a tragic death, though.
If you look up into the parking garage, you see exactly where he fell from as there is a guy looking down and a nice chunk of wall missing. It gives you a good perspective of how far this car actually fell!
We are going to start of with a well-meant attempt by Chrysler to meet the oil crises from 1973 to 1980. Introducing the Cricket!!!!
1973 Cricket
This car was actually a US spec’ed Hillman Avenger.
It featured the Avenger’s 1.6 liter pushrod engine. This car’s top speed was 84 mph and took a merely 19.8 seconds to get to 60 mph (I bet you were thinking 100 mph!!).
The car was horrible slow and because it was detuned for as part of the US requirements it ran poorly.
Yes that’s correct for the 100th year of production Ford build a total of 6 Model T-100 to commemorate the year.
These weren’t restored cars, they were all new parts. The bodies were made in Sweden, coupled with available aftermarket. The engine, suspension parts, transmissions were created from the original drawings.
Model T Reproduction Engine
The T's transmission - could replace the original unit, however the gear pattern is not the same so the internal will not match up.
This is it. The beginning of it all. What were they making in 1901?
The top producer was the Locomobile car company with a total out put for the year 1,500 cars.
Winton was second with 700 cars.
Oldsmobile (ahh one we’ve heard of!!) was third with 425.
White came in fourth with 193.
Autocar was next with 140.
Knox was sixth with 100.
Rounding out the bottom was Packard and Stanley with 81 and 80 respectively.
This is a 1901 Winton Racer..what's the guy in the front doing?
1901 Autocar
The 1901 Autocar has a shaft-drive engine, powered with a water-cooled, two-cylinder, horizontal-opposed engine in the front of the car. The gasoline tank and battery box were under the front seat.
I was reading the other day and I came across a car manufacturer that I hadn’t heard of prior and yes it was an American car maker. The maker was Velie.
1911 Velie passenger car
Like some car manufacturers Velie started out as a carriage maker (as in horse and carriage). The owner was Willard Velie and we received his funding from this mother who was the wife of John Deer. Yes that John Deer. It’s not exactly clear if John Deer was is father, but we’ll assume it was so.
Willard created Velie Motor Vehicles Co. in 1908 and produced their first car in 1909. It was a 4 cylinder and sold 1000 units and were sold though John Deer dealerships. The 1909 and 1910 models primarily used existing engine but in 1911 build their own. In that same year the Velie car participated in the Indianapolis 500 and finished 17th out of 46.
1911 Racer
That helped keep car production was at 3,500 vehicles a year. By 1914 Velie added a six-cylinder side-valve Continental engine to the mix of power plants. and by 1918 only offered six cylinders. The car became so popular and reliable that a few folks in Louisiana name a town after the car.
In 1918 Velie won the race at Pikes Peak which helped increase production to 9000 a year cars by 1920.
In 1928 they introduced the an 8 cylinder engine a Continental straight eight and were a roll so to speak. (Not to mention their little side business for producing air planes.) However that was not to be, Willard died in late 1928 and Willard Jr. died a few months in 1929 later. That ended the Velie Motor Vehicle Co.
John Deer company bought the plant and well they sold a few tractors now and then.
I bumped in to Bill Holtzclaw from Cartersville, Georgia, virtually (Facebook) and he shared a few pics and some detail on his restoration of a 1967 Olds F-85.
Bill's F85
“I am doing a full, frame-off restoration on this 1967 F-85 Club Coupe. It has a convertible frame, 442 suspension, steel crank 330, .030 over with W-31 cam and 2” intake valves, close ratio Muncie 4 speed and heavy duty 3.91 posi rear. It is a radio delete, heater delete, carpet delete car with the factory cloth and vinyl interior. The drive train is built and the chassis is being assembled. The interior is done, the chrome and bright work is done. Next, we’ll pull the body and put it on a rotisserie. It will be two-tone Crystal and Midnight Blue.”
“I’ve had a lot of interest in this project from some of the leading Oldsmobile collectors in the country. It is my version of what would have been a 1967 W-31, which was introduced in 1968. All of the parts to build this car back in the day were available as either RPO options or over-the-counter upgrades. The W-30 package was available as an over-the-counter package in 1967. The W-30 cam and the W-31 cam are one in the same, and the OIA kit will work for both small block and big block cars. So, it was a possibility! ”
The upholstery turned out awesome! He used NOS fabric for the seat inserts. The car was a factory carpet delete car with a near-perfect vinyl floor covering. “I cleaned it and had it dyed the color blue (same as dash pad) that I wanted. It looks absolutely brand new! I had seat belts custom made to stock appearance, and the standard steering wheel came out nice, too.”
Check out the vinyl floor covering
“I had the gauges restored by R&M restorations in Greenville, SC. The odometer was re-set to zero.” The dash bezel was restored by Chrome Tech USA. They repaired the 44 year-old plastic, re-chromed it and then detail painted it. The radio and heater delete plates were purchased from Red Venom Enterprises. “They only make the radio plate, so I purchased two and trimmed one to fit the heater control panel and the PRNDL panel. ”
Bill did the polishing himself
He installed a Sunpro Mini Tach in place of the factory clock. Looks like it came from the factory that way!
Great Job - Bill!!
Final Product
Bill is also the owner of a 1967 Oldsmobile F-85 Town Sedan with “Police Apprehender” package. It has the HiPo 330/320 hp, Heavy Duty Jetaway and 442 suspension upgrades.
Nice!!!
Might be why he’s known as OldsMoBill. “I am also known as the “Oldsmobile Police”!” Bill states.
Bill, I hope you check back with your status from time to time and thank you for sharing.
I thought I’d take a minute finish up the write-up on the very first upholstery job. I finished it up a two weeks ago and really missed driving the Mustang, but that’s what happens when you do your own work and you can only fit it between all the normal life stuff that needs to get done.
Yes, as I was reminded twice by a couple of car acquaintances, I used a kit, some say they aren’t much different from slip covers, but as you can see in my shots here that’s a bit of an understatement.
Now these next two videos are not all that great but I think you can see the removal of the back and the fasteners. I’ve worked with these type of fasteners before in my father’s body shop (back in the early ’70s) nearly all door panels and seat back were fastened in that way. They work really well but bend them (and they do bend easy of they aren’t aligned with the hole and pressure is applied) and you’ll have to spend sometime reshaping them, even then they might not hold properly, or replace them.
Check out the videos:
Here are a few more photos and the finished product. Not to bad for my first one. I have the passenger’s side to do.
With the plastic seatback removed.
Needed to remove the back release
2 piece
release removed.
Helpful hint: All the hardware and fasteners have to pass through upholstery. Rather than try to cut holes, I made X cuts and pressed the screw or hardware through. This made it as tight as possible.
Markings on the Foam
Good shot of the cloth sleeve with the wire passed through.
Here you would pass the hog wire while in the hog-nose pliers through the cloth between the upholstery and the wire. You then have to shove this down between the two pieces of foam and grab a spring.
Finished product.
Replacing the seat track was done before I married the bottom and back. Placing it back in the car was a little tricky..until I figured out that moving the set on the track was the way to get the studs to drop back in to holes in the floor board.
Over all this was not as tough as I thought it would be. The passenger side will be quicker. I’ll post the final product on that side.
This is a great show of the main gallery. In this clip they have just placed the AJ Foyt #8 Corvette on display and are setting up a C6 Grand Sport next to it.
