The most American cars on the list are Honda Accord and Element at 80% and 85% respectively, the Ford Explorer at 85% (90% for the 2010 model year) and the Dodge Grand Caravan at 82%.
As I start gathering the different parts for all the new mods for my ’70 Mustang one thing I’m sure of is that I want a little more ‘bling” under the hood. I think the Ford blue engine paint with the brushed nickel look of the current intake need something to offset that color scheme. I’d like to do most of the brackets for the power steering, alternator, and ac compressor all in chrome. However that’s not going to be possible, if I rely on aftermarket/stock suppliers, as most of my brackets are custom-made. (That’s what you get when you keep the 6 cylinder components when you do a conversion to an 8 cylinder.) So I’m going to make do with what I can find and the rest will remain iron.
Now with the cost of all this mods looming on the horizon and having less than the average budget, I’m trying to upgrade at least the tension portions of the Alternator, A/C and the power steering to chrome. My goal is to replace them with heim joints w/adjustable rods between them. These are not inexpensive and often require some modification.
So in the pursuit of this end I purchased a kit from Summit Racing for my alternator. This was an all aluminum kit and only advertised as being for a ‘stock” 302 engine. So going in I knew that it might not work at all. This turned out to be correct except for the heim joints and the threaded aluminum rod.
So I going to use those for the tension rod for the alternator. However, it wasn’t chrome and had a very heavy coding to make it look like brushed nickel. The goal for this pieces was to polish it up and see how “bling” like it could look. This would be a series of repeated sanding, buffing and polishing.
I used my Dremel, sanding disks and buffing and polishing wheel, 200 and 600 grit sand paper and Purple Metal polish, cotton rag (ok..fine it was an old t-shirt) and a vice.
Dremel buffing while and 160 grit sanding disc
Now the 160 grit disk might have been a bit much but the coating was pretty tough and the disc made quick work but did leave a few marks on the test sample that might have causes a bit more work with the lighter grits.
This is actually purple in color and gritty like rubbing compound.
In short the process started with hitting the test piece (one of the stock bracket parts that wouldn’t fit) with the 160 grit disk via the Dremel. Next I ran the 220 grit sandpaper (by hand) over the aluminum and then the 600 grit and then with the buffing/polishing wheel via the Dremel with a coating of the Purple metal polish. I switched it up by using some metal polish with the 600 grit sandpaper.
It took a lot of elbow grease and a couple of hours. Here is what the test piece looks like. You can see the aluminum w/coating and polished portion.
Chrome? Absolutely as shining as chrome.
Now there are some in perfections in the aluminum and if not being careful with the sanding you can leave gouges but generally you can get this type of shine and it looks very close to chrome without the cost, just some elbow grease.
Next will be the polishing of the actual rod that will connect the two heim joints (they are already polished steel). (I’ve already started, but you won’t see it until it complete.)
As I have mentioned, I love the old station wagons. I love the fact that they are being restored. I even like the fact that many are getting the power plants they needed back then transplanted. Although I have to admit I am growing bit tired of the seen a “Corvette” engine between the front wheels – maybe just the fact that they left the “Corvette” labeling on them.
There were some beauties at this show.
All Custom Wagon 1
Nicely Done.
Here is a nicely done Plymouth:
Plymouth Wagon
Love the Nose of this Ply - They really didn't want any one near it.
Now you can call me a DORK but I love this Ford Wagon.
Ford Wagon
Love the Grille
Hey..I even love the hood ornament.
This Torino Wagon, although banged up and hood all mis-aligned, it’s still a keeper with good tread and not too shabbby wheels. I think it’s a keeper.
Ford Torino Wagon.
Lowered but still standing tall was this beautiful Chevy Wagon.
Loving the paint and the roofline!!
I’ve got a few more post coming up shortly before wrapping the Goodguys’ car show trip.
This is the first of Average Guy’s “Feature Car” blog entries so a little preamble is required. My daily driver is my 07 C6 Corvette and I love that car, but you won’t see new or newish exotic cars in this feature. Nope, it will be mainly comprised off beat, older cars including some muscle cars, pickups, utility vehicles and what not.
So I’m starting off with a pickup, most folks haven’t heard much about. It’s the Powell pickup.
These are a bit odd-looking pickups. See for yourself:
1956 Powell
These trucks were a collection of parts from other American car manufacturers. They were produced 1954 – 1957 with about 1000 units created and I do mean created!!
They were built on early 1940’s Plymouth and Dodge chassis, with part of the bodies being producted of steel, front ends made from fiberglass and tailgate and bumpers made of wood at one point. In most cases the engine was straight 6, Mopar‘s 201, but they did use a few other power plants in the same family, even some industrial engines.
One interesting notes is that the chrome used in the grille was from 1950 Ford rear door. But the most unique feature was the cylinder shaped compartment that slide out of the rear of the trucks for fishing pole storage.
Unkept Powell Pickup with Fishing Pole storage
They also produced a wagon (station wagon-like) with the same storage as an option.
As I get ready to start the new round of mods for my 1970 Mustang Coupe, I’m reminded of a couple of issues that came up when I was assisting a fellow Mustang owner doing a trans – transplant.
The first tip is partially dependent on what stage you are in of your restoration.
He has already finished most of the interior when the a transmission he wanted to add became affordable, it was a good deal…saving some $$$$.
He had decided to do the swap and add a short shifter. This of course requires the removal the bezel and the current 3 speed shift lever, which is easily done from inside the car.
Bezel and Boot
In the course of removing those two parts, he found that the opening cut in the new carpet was not going to allow the access necessary. An attempt to ‘widen’ it was successful but left a bit of a jagged slit. Additionally, while removing one of the screws it snagged the carpet and pulled a few loops out. Can you guess what the tip is? Yeah…remove the carpet and if possible make the swap before you put new carpet in.
One other quick tip is to apply a little silicone spray to the shifter to help slide the boot off..oh…yeah…removing the shift knob before the boot is a good idea…..DON”T ASK!!!!!
From square boxes to sloping roof lines to coke bottle shapes, car lines have evolved. Sometimes they just went way wrong.
I’ve had my fair share of cars and their shapes and lines were polar opposites. My 1966 Imapla (my first car) was long and sleek, my next car was a Dodge Dart boxy but with a good roof line. Oh but it got worse, my first nearly new car was ….wait for it…..a Ford Granada. Yes…boxy…maybe a little roof line, but it got me around.
After that a series of car including a ’70 Chevelle (you know those great lines), a European Ford Escort (while stationed overseas) and a 83 Camaro (that had great lines on that one). I owned one more Granada and a VW Rabbit (diesel) and two Toyota Celicas ( like the lies of those), a couple pickups and my two Vettes and my Mustang. They spanned decades and many different design lines.
Some of the worse, in my opinion, were some of the best-selling and some that go for huge money now that they are classic muscle cars.
The absolute worse were the pumpkin or watermelon seed cars (that’s my coinage).
Here’s an example: 1996 Chevy Impala
A far cry from my 1966 Impala’s lines
1966 Chevy Impala
Now, I was looking at the lines of my ’70 Mustang and I’d have to say compared to the ’70 Dodge Super Bee the lines (and include the graphics, moldings and even panel seams) the Mustangs lines are much cleaner.
Here is an outlined image of the Dodge:
Dodge
I tried to be fair with my hand drawn lines. The flow of the graphic and their awkward end as they go to the relatively square door make it almost look like the designers said..”OH Crap!!! We forgot the door!!” The fenders have nice lines, as do the quarter panels, but in total it isn’t smooth. HOLD ON, before any of you Mopar folks get all worked up, I’d own a Dodge Super Bee, in a heart beat, especially if someone parked it out side my house and tossed me the keys…and I drive that 383 like I stole it!!!
Now look at the lines of my ’70 Mustang…(are you sick of seeing it yet?)
70 Mustang lines
Just the forward edge (hinged) of the door being shaped it a big plus in my opinion. The sloping of the roof-line into the trunk is another smooth difference, and keep in mind this is just the coupe, not the fast back for the sports back, relatively speaking my Mustang is rather square compared to it siblings, the Mach I and Boss models. Compare the side window openings. The Dodge is very angular, the Mustang’s has a smoother flow.
I could go on and on, we could talk about the 70’s Volares or the even move into the 80’s and talk about the Ford Fairmonts or Chryslers K-Car (I can hear Bill now!!!) but let me hear from you. What do you have to say about car lines, past or present?
Tokyo 17 Car Design Forum opens for registration. Our Tokyo 2017 Car Design Forum has launched, and the website is open for registrations now. More News …
Hyundai-Kia design chief outlines car design philosophy – Interview. by: Roger Stansfield. Materials at the heart of the Paris Motor Show. 20 Oct 2016 …
I often have several articles going at once. However, since I don’t to this for a living (yet) daily activities, like driving to work, often give me ideas for a quick blogging episode, the other article wait.
Like the other day after work, which was a good one at the old salt mine, a rarity, I was headed to my work out session with my “very understanding” better half and the car in front of me made think of a particular feature of a car’s design.
In this case I need to give you an insight into some of the things that go on in my head while driving.–Don’t worry this is the PG version–. The most important need is to be very diligent as to notice other corvettes..got to keep the wave alive…” missing a wave is a violation of the corvette code. (Yeah…really…and you thought all you had to do while driving a Corvette keep an eye out for ‘smokey’.) Second most important thing is to keep an eye out for old smokey. Then there’s the sizing up of your road-mates as you are stopped at a red light. After those serious tasks, I look at the tail end of the cars around me to see if they are two pipes or one and of course size (exhaust envy – it’s real!!). One tail pipe means it is a “girlie man’s” car and two or more is of course the opposite. Hey… it passes the time while sitting in traffic.
Normally, I check out cars of all types for tailpipes, Honda, VW, all the domestic brands and models. Most only have one and some have the bumper designed for two but still come up short one pipe.
So today, I’m sitting a traffic light at Broadway and Aviation Highway behind a Saturn Overlook cross-over vehicle. Habit takes over and I noticed that there was only tail pipe – girl’s car. As I looked closer the rear end, I noticed what appeared to be a factory designed space for a second tail pipe. But the gap wasn’t just a mere indent where the second should have been. It was a very wide space. The design of that of its exhaust system on the end has muffler that looks like an over sized World War II canteen. The tailpipe sticks out of this elongated canteen at about a 70 degree angle. The muffler is exposed and hides the rear suspension. In the picture below you can see the dual exhaust.
Saturn Outlook with Dual exhaust
Now picture the left one removed without the muffler. What you’d see is a cut out and the left independent suspension structure. Why not close that off? The real reason is cost of having two different rear bumpers’
Below is a picture of a 2008 Outlook and you can see the exposed rear suspension.
Exposed suspension
So while you are driving, look at the backend of the car in front of you. You’ll see that Honda Civic with a place for a second the extra exhaust pipe and you’ll think…”Really? It was designed for a dual exhaust?
