Tag Archives: Mustang

1973 Mustang – Project Sports Roof – Vacuum System Part II

By | | , , , , , , , ,
2 Comments

Thanks for checking on #ProjectSportsRoof.

 

So here is the last set of initial questions.

Here is an image of the current set up:
[Image: Vac-14-L_zpsndlzgozn.jpg]

[Image: Vac-13-L_zpsgbppofla.jpg]

Any diagram I find has the hose vacuum from the Distr going to the Valve assy.

The Valve assy has nothing attached which is located on the front right side next to the alternator on the water pump housing.

[Image: Vac-31-L_zpsyrpi8chf.jpg]

The diagram for the 1972 351C shows that instead of going directly to the carb, the hoses from the distributor vacuum run to the Valve Assy. There also seems to be a second line running from the back of the distributor (in the diagram) – but that isn’t very clear.

Any ideas? Clearly the car runs without any of these connected – do I just plug them all?

Tim

1973 Mustang – Project SportsRoof – Vacuum System Part I

For the purpose of these series of posts let’s assume that I want to seriously limit the performance and power of #ProjectSportsRoof’s beautiful 351C and restore it back to factory configuration. Now if you are expecting an …
1973 Mustang – Project SportsRoof – What are You Gonna …

#ProjectSportsRoof. 73-17. 1973 Mustang Project Sportsroof – Engine Walk-Through. There is a quick walk-through of the 351C tucked between the fenders of the 1973 Mustang Sportsroof. (It took about 5 takes to get this …

1973 Mustang – Project SportsRoof – This Just In – Cooler and Gauges

By | | , , , , , , , ,
1 Comment

Just received a few more parts in for the 1973 Mustang project.

Check out the video.

 

Thanks for reading.  Keep checking on #ProjectSportsRoof.

Tim

1973 mustang mach 1

1973 Mustang – Project SportsRoof – Money!!

#ProjectSportsRoof will be the way I want it, which I haven’t nailed down yet, so suggest way by dropping me a comment (got your crate motor idea swimming around in my head, Bill) and that will happen fast or slow and cost …

1973 Mustang – Project SportsRoof – Compression, Rods and Heads Part II

By | | , , , , , , , , , , ,
2 Comments

So after inspecting the head further, I noticed  a few more reasons to have them reconditioned.  Take a look:

Gonna Need some touching up.

Gonna Need some touching up.

 

 

 

 

 

 

 

 

 

 

As you can see there a lot of rust and old stuff plugging up some of the water passages.

The heads were sent out to a local machine shop run by an old hot rodder.

Here’s a quick video of the valves that were removed. You can see the build up as the oil (from the tappet hole) and the gas was continually ignited by the spark plug.

The good news the heads are back and installed.  The bad news in my haste to get the car back together,  I forget to get some shots of the completed heads.   By the time I realized it was too late to go back.

 

 

The Cleveland is running strong, but needs a lot of work on the vacuum system and – I’m thinking of replacing the carb.  Send me your on what to replace it with.

Motorcraft?  Holly?

Thanks for reading.

Tim

#ProjectSportsRoof

1973 Mustang – Project SportsRoof – Compression, Rods …

Thanks for check in on #ProjectSportsRoof. If you remember a of couple months back, shortly after bringing the ’73 Mustang home, I conducted a compression test on all.
1973 Mustang Project Sportsroof – Engine Walk-Through.

Next up will be the install Pertronix system and cap and rotor, then plug and wires. Thanks for reading and drop me a note. Tim. #ProjectSportsRoof. projectsportsroof. 1973 Mustang Project SportsRoof – Interior Walk-Through.

IMG_20150923_162001327_HDR

Lisa’s 1973 Mach I Restore!

By | | , , , , , , ,
Leave a comment

I love it when a fellow car enthusiast shares their projects.

This is Lisa’s 1973 Mach 1

1973 Mach I

1973 Mach I

 

 

 

 

 

 

 

 

 

Saved after sitting in a junk yard for 21 years.   WAY TO GO LISA!!!   Daunting project to be sure…but you GOT THIS!!!

Lisa73MachI-b Lisa73MachI-c

Lisa wrote:

“Thank you. That is the stock engine out of the original car. The car sat in a junk yard for 21 year before I got it, I thought for sure that it would be too far gone to do anything with but I was completely wrong. The fluids still looked new and once we had the engine out and sitting on a pallet, we rigged it so we could see if it would turn over and sure enough it did. Mine is also a 2v with a 4brl intake. ”
“I wanted to rebuild the engine as affordably as possible so the cam and lifters and the valve guides and seals are the only thing new other than the valve covers which I had to get because sand blasting the factory ones was pointless. The oil pan a friend of mine bought for me after I helped him install his transmission.”
My husband and I own a performance shop that also does machining and I was able to learn how to do the machining on my heads and block to save money on labor. I’ll definitely keep you posted as I progress. I hope you decide to get that mustang and restore it. I would love to see pictures.
You can definitely use my pictures on your blog.”

Here is the engine for Lisa Mach I.

So nicely done!!

Getting ready for some paint!!

Lisa73MachI-Engine2

So nicely done!!

 

 

 

 

 

 

 

 

 

 

 

Lisa, we are looking forward to seeing the progress on this beauty!!!

Oh…and google #ProjectSportsRoof or just stop by http://www.agcarrestoration.com/ and you can follow the progress on my 1973 Sports Roof.

Thanks again for sharing your project.

Tim

#ProjectSportsRoof

 

1973 Mustang Project SportsRoof – Exterior Walk-Around

Welcome back to #ProjectSportsRoof.  I run my car projects much like I run my IT projects.  You always have to know where to start and know the end game.   As with any project that isn’t being built from scratch, in other word, you have to work with what you’ve got, …

1973 Mustang – Project SportsRoof – Compression, Rods and Heads

Thanks for check in on #ProjectSportsRoof. If you remember a of couple months back, shortly after bringing the ’73 Mustang home, I conducted a compression test on all the cylinders.  The 351C was running rough (to put it mildly) and smoked like a pile of tires on fire (only the smoke …

1973 Mustang Project Sportsroof – Engine Walk-Through.

Next up will be the install Pertronix system and cap and rotor, then plug and wires. Thanks for reading and drop me a note. Tim. #ProjectSportsRoof. projectsportsroof. 1973 Mustang Project SportsRoof – Interior Walk-Through.

 

1973 Mustang – Project SportsRoof – Compression, Rods and Heads

By | | , , , , , , , , ,
5 Comments

Thanks for check in on #ProjectSportsRoof.

If you remember a of couple months back, shortly after bringing the ’73 Mustang home, I conducted a compression test on all the cylinders.  The 351C was running rough (to put it mildly) and smoked like a pile of tires on fire (only the smoke was blue).  Clearly there were some issues.

Here are the links to the posts were you can view the compression tests – RIGHT BANK – LEFT BANK.

To summarize, the cylinders topped out like this:

Cylinder 1 (Left Bank) – 130

Cylinder 2 – 25, 35, 60, 90 (Fail!!!)

Cylinder 3 – 140

Cylinder 4 – 135

Cylinder 5 (Right Bank) – 160

Cylinder 6 – 155

Cylinder 7 – 160

Cylinder 8 – 140

Clearly cylinder 2 has a serious problem and it could a host of things.  Since it was so bad, I didn’t feel it necessary to conduct a wet test and just planned out pulling the heads.

Well the time came to get take care of that and it wasn’t long to disassembling that it was clear what was wrong with cylinder 2.

What the....?

What the….?

At first we thought…”Hey Cool!!! Extra parts!!” But of course that’s just not the case!!

Tappit-3

 No extra parts.

It couldn’t be that the tappet just rolled there. Something else has to be an issue.

Oh…maybe…one of these was the problem?

Rods

Ya Think???!!!

Close inspection of the piston in cylinder 2 showed no signs of impact. As it appears thus far, that the bottom end of the engine is in good shape and the compression numbers for all the other cylinders and we bolstered that assumption with a visual inspection.

Think the heads need to be rebuilt and machined?

That’s coming up.

Thanks for reading.

Tim

#ProjectSportsRoof

IMG_20150923_162001327_HDR

 

1973 Mustang – Project SportsRoof – Compression Test Part I

Thanks for reading. Tim. #ProjectSportsRoof. projectsportsroof. 1973 Mustang Project Sportsroof – Engine Walk-Through. There is a quick walk-through of the 351C tucked between the fenders of the 1973 Mustang Sportsroof.
1973 Mustang – Project SportsRoof – Compression Test Part II

#ProjectSportsRoof. projectsportsroof. 1973 Mustang – Project SportsRoof – Compression Test Part I. I’ve done all the clean up and all the adjustments necessary to get a good reading on the health of the ’72 351C engine in …

 

1973 Mustang – Project Sports Roof – Fender Fitment – Extensions I

By | | , , , , , , , , ,
Leave a comment

With still some adjustments need on the fenders, I need to tackle the fender extensions.   If you recall the first video at the beginning of the fender fitment series of post you can see that the there’s no way it will fit (view the link HERE).

As I fitted them up here is what the left site looked like (this is after the altering the hole):

 

Gap

Gap

Pretty large gap.

Pretty large gap.

The right side was better with almost no adjustments to the holes.

Not to bad right out of the box.

Not to bad right out of the box.

Almost acceptably gap

Almost acceptably gap.

This video clearly shows the difference in quality of the fenders.  Quality control measures are that great.

Clearly the right side was much better formed then the left.

With a little more adjustments with a body dolly I was able to close the gaps.

Thanks for reading.   Next up “What caused the compression issue?”

Tim

#ProjectSportsRoof

1973 Mustang – Project Sports Roof – Fender Fitment Part I

Nothing But Curves – Should have packed the Vette!!!!! Welcome back to Project Sports Roof (#ProjectSportsRoof). We stripped the old fender and retained all the usable parts. Next we are going to fit the new fenders up to the …

1973 Mustang – Project SportsRoof – Fender Removal

In case you didn’t notice, the fenders that were on #ProjectSportsRoof look as though car had driven into a half pipe at a skate park. Left Fender – major.

1973 Mustang – Project Sports Roof – Fender Fitment Part II

By | | , , , , ,
Leave a comment

In these next two videos, you’ll see just how ‘off’ these fenders are in some areas and surprisingly how well they fit in other areas.

If you have an experience or a hit for anyone taking on this part of a restoration – drop a comment here and we’ll share them.

 

 

 

Thanks for reading.  Lot more coming up.

Tim

 

1973 Mustang – Project Sports Roof – Fender Fitment Part I

Nothing But Curves – Should have packed the Vette!!!!! Welcome back to Project Sports Roof (#ProjectSportsRoof). We stripped the old fender and retained all the usable parts. Next we are going to fit the new fenders up to the …

1973 Mustang – Project SportsRoof – Fender Removal

In case you didn’t notice, the fenders that were on #ProjectSportsRoof look as though car had driven into a half pipe at a skate park. Left Fender – major.

1973 Mustang – Project SportsRoof – Money!!

#ProjectSportsRoof will be the way I want it, which I haven’t nailed down yet, so suggest way by dropping me a comment (got your crate motor idea swimming around in my head, Bill) and that will happen fast or slow and cost …

1973 Mustang – Project SportsRoof – Front Valance and Old Fenders

By | | , , , , , , , ,
Leave a comment

Thanks for check back with #ProjectSportsRoof.  While I’m headed off on vacation I’ve scheduled a few post to get published while I’m out.

As a note the progress is moving well and I’m posting these in order, but they are delayed by a couple of weeks.  I’ve nearly completed the fender install – still have a few adjustments to make and you’ll see these posts coming up.  Taking advantage of various opportunity in the course of a project some times has you stop on task so to take an opening to get another task done.  This is the case here with the 351C engine.  I had a chance to get the some engine work done at a great price so I’ve jumped to that task and put the others on hold. Those post will be coming up soon.

To remove the fenders you, of course have to pull off the front valance.  This one happened to be a new after-market piece.

 

When you swapping out any original parts or components, you want to try to salvage any sub-components or parts that are still functional and look good.  Stripping these old fenders included saving the fender extensions, side makers, bolts, badging etc.

When I’ve capturing these on my Android, I trying to keep them short and often use the wrong name for some of the parts, hence Fender Ends = Fender Extensions.

🙂

 

Here is a look at the fender extensions.

If you’ve seen any of my other project you’ll notice that I try to keep things – organized – some what.

 

There’s more coming up on the fenders and the cause of the low compression on cylinder #2 – it’s not what I thought!!!

 

Thanks for reading.

Tim

#ProjectSportsRoof

1973 Mustang – Project SportsRoof – Fender Removal

In case you didn’t notice, the fenders that were on #ProjectSportsRoof look as though car had driven into a half pipe at a skate park. Left Fender – major.
1973 Mustang – Project SportsRoof – Compression Test Part I

Thanks for reading. Tim. #ProjectSportsRoof. projectsportsroof. 1973 Mustang Project Sportsroof – Engine Walk-Through. There is a quick walk-through of the 351C tucked between the fenders of the 1973 Mustang Sportsroof.
1973 Mustang – Project SportsRoof – Compression Test Part II

#ProjectSportsRoof. projectsportsroof. 1973 Mustang – Project SportsRoof – Compression Test Part I. I’ve done all the clean up and all the adjustments necessary to get a good reading on the health of the ’72 351C engine in …

73-17mach 1

 

 

1973 Mustang – Project SportsRoof – Fender Removal

By | | , , , , , , , , ,
Leave a comment

In case you didn’t notice, the fenders that were on #ProjectSportsRoof look as though car had driven into a half pipe at a skate park.

Left Fender - major dent a lot of rebuilding necessary

Left Fender – major dent a lot of rebuilding necessary

Right Side Fender - lots of crinkles, a few creases and good size dent.

Right Side Fender – lots of crinkles, a few creases and good size dent.

Now, these are fixable, with a lot of  heating and dolly work and bondo – but I’m trying my luck with re-pops and that’s what is coming up in the next few post.

 

 

 

Drop me a know if you have a project you are working on.

Thanks for reading.

Tim

#ProjectSportsRoof

1973 Mustang – Project SportsRoof – What are You Gonna …

#ProjectSportsRoof will be the way I want it, which I haven’t nailed down yet, so suggest way by dropping me a comment (got your crate motor idea swimming around in my head, Bill) and that will happen fast or slow and cost …

Project Large Marge: New Fuel Tank and In-Tank Fuel Pump on a 1973 Mustang

Our 1973 Mustang is 42 years old, which means the gas tank has seen 42 years worth of various qualities of gasoline, sludge, condensation, residue, and most likely rust. Since we’re upgrading the engine to a blown and injected (Holley Terminator EFI) …

 

 

 

1973 Mustang – Project SportsRoof – This Just In #3 Floor Pans

By | | , , , , , , ,
1 Comment

Thanks for following #ProjectSportsRoof.

Another batch of parts showed up the other day.  Take a look.

 

Thanks for reading.

 

Next up for #ProjectSportsRoof – sway bar installation.

 

Tim

 

IMG_20150923_162001327_HDR

1973 Mustang Project SportsRoom – This Just In #1

It’s almost like Christmas every time part come in for #ProjectSportsRoof. Here’s what came in this week: Fresh from North of our border are these wood insert for.

1973 Mustang – Project SportsRoof – This Just In #2

Received a set of reproduction front fenders for the 1973 Mustang #ProjectSportsRoof. They will be replacing these: Right Side Fender – lots of.