As we close out the year that was 2010, I celebrate the first year anniversary of Average Guy’s Car Restoration, Mods and Racing.
Over the past year, I’ve enjoyed jotting down my thoughts and experiences. Mostly, I’ve enjoyed hearing back from readers here on my Word Press main site and in other social media.
This past year I’ve seen the page views on this “one man” blog go from just a couple per week, to nearly 1500 a month. Not bad for a non-commercial blog, with no paid advertising. So THANK YOU. I hope to hear from and read your comments and views in 2011.
What’s coming up in 2011? Mods on the ’70 Mustang, tweaking of the LS2 on the 07 Corvette and I’ll continue with the Auto Factoids in their new format. You will see more mini engine series, kicking off the New Year one of my favorites Chevy’s 283 and there will be more racing events, test ‘n’ tunes and Mom and Pop racing teams highlighted. There will be more contests and DVDs to give away and project updates from readers. Oh…I’m coming out with the Average Guy’s 2011 Calendar look for that on-line.
It’s going to be a fun new year.
To you and yours – may 2011 bringing nothing but happiness and joy.
What you will see unfold in these updates is an exercise in project management for the modifications. When I originally scoped out the components for the 302 that replaced the 250, I used a similar process, but very detailed. I wasn’t overly concerned with improvements other than what a dropped in 302 would provide over that tired old straight 6. (Clearly..I left the 3 speed manual trans in it.)
But this time it’ll be different. There is a lot to do and unlike the previous rebuild, money will be tight and free time limited. The main goal I have is to keep the car in operation in between stages of modification. This will take a clear and well laid out plan, where issues similar to the installation of the dash pad before the pillar post trim arrived (doh!), could be more than just a cost in time.
Below is a high level sketch of what I’d like accomplish with the Mustang. I’ll update this list with more details as I figure which brands, sizes and the like that will be used. Over on my Facebook pages I have already received some feedback and suggestions and I’ll post these up here in some cleverly titled entry.
So give me your suggestions or opinions and as the progression goes even tell me if you don’t like the choice and why.
Brakes and Suspension:
– Upgrade to 4 wheel disc (Brand and size TBD)
– Replace front and rear stabilizer bars (Brand and size TBD)
– Control arms already replaced
– Rebuild power steering
– Shocks already upgraded
Exhaust:
– Add cut-out before mufflers
– Extend tailpipes to exit rear
No other changes anticipated
Interior:
– Addition of upgrade dash and interior lights
– Possible upgrade of all gauges
– Replace front seat belts with 3 point harness
– Carpet replaced
– Seats re-upholstered (upgrade to Leather/Cloth?)
– Paint lower doors
– Tilt steering wheel (Flamming River?)
Training:
Transmission
– Option 1 – Manual 4 speed with Hurts shifter
– Option 2 – T5 5 speed
– Rear Differential * Unsure if upgrade is possible or required
Engine:
* 302 stays
– Replace intake (Brand and size TBD)
– Replace 650 Holley (Holley 750 Avenger)
– Replacement of heads for more performance (undecided)
– Add custom mounting and tension for Power Steering/Alternator
– Remove Fan and replace with electric
– Add more chrome to engine (but not too much Bling..hate too much Bling)
Exterior:
Paint stays except:
– Blacked out rear light deck
– Black Hood stripe (1970 Boss 1970 302 or 1970 Mach 1) – See images below – What do you think?
– Blacked out grill
– Black Front Spoiler
– Black side Boss 302 Stripe (w/o the Boss) (dependent on hood choice)
– Magnum 500 wheels (newer version, not originals)
Hood lay outs:
Mach 1 Hood...Perhaps my favorite...currently not considering adding a scoop
Boss 302 Hood lay out
O.K., let’s hear your thoughts. They will automatically appear to the right of this posting and I’ll add the good ones in the update posts.
Thanks for reading.
Tim
Readers comments and suggestions:
Byron McElfresh December 6 at 9:09pm Report
I seen your asking for advice on heads for a 302. I built a 302 that was .040″
over bore, The larger hyd. roller ford performance cam, used edelbrock rpm
heads, i did a little clean up and evened out the valve bowls, flat top
pistons, a 750 holley Street advegner carb, rpm intake, 1 3/4″ headers, and it
made 416 hp at 6000 rpm, and 349 tq. on the dyno. in the 60 Falcon with 3.73
gears, and a 4 speed,( the guy really needs an auto trans or get a shifter that
won’t granny shift speed wise!!!) But he still ran a 12.61 at gateway.
Wow, that’s pretty good. My 302 is bore .030. Hooker headers and 65O holley. I
wasn’t planning on changing out the cam. Now the rear end great. I just can’t
do the automatic trans though!
Byron McElfreshDecember 6, 2010 at 11:43pm
Re: Hi Tim,the 302
lol-the reason I think the guy should o to an auto trans is the ultra slow
shifts he makes with the old toploader! It’s a very painfully slow 2-3
shift!!!You can almost hear the multiple double clutches! yikes! lol
Tim Sweet December 6 at 10:11pm
good point
————————————————————————
Philip Daly December 6 at 8:58pm Report
351w
Tim Sweet December 6 at 9:36pm
Thanks Philip, But won’t that reduce compression? How much would you gain with
351w heads?
—————————————————-
Terry Wallace December 6 at 8:47pm Report
Ford Motorsports usually has some really great deals on 302 old school engines.
I would check there first. When it comes to flow numbers im finding through my
own testing at my machinists shop,,,,,most numbers are bullshit. beware and
test flow numbers using a reputable shop.
Tim Sweet December 6 at 9:35pm
Thank Terry. I’m with you on the numbers game…happens a lot even with
Corvettes. Regards
—————————————————————–
Bill Rice December 6 at 8:46pm Report
Trick Flow Twisted Wedge heads, Great gains in HP and Torque.
Tim Sweet December 6 at 9:42pm
Thanks Bill – what do you think those number might look like over a 302, bore
Corvette Hangout December 6 at 8:28pm Report
C&C aluminum heads with small chambers to get higher compression larger valves
and install 150 shot of nitros.. CorvetteHangout
Tim Sweet December 6 at 9:44pm
I can get behind the higher compression..but I haven’t decided on NOS yet.
Thanks.
_————————————————————————-
Fatherlarry Monaco
1969 and 1970 Boss 302 heards and intake will work great.
Tim Sweet That was a thought I had as well.
2 seconds ago · Like
————————————————————————
Roy Oberg Aluminum is the way to go, go with a smaller combustion chamber that will give you more compression and less chance of spark knock.
about an hour ago · LikeUnlike
#
Tim Sweet 100% on board with the smaller chambers.
2 seconds ago · Like
11/10/14 – The first Dodge is produced and on the same day 11 years later Ford built its first Tri-Motor airplane.
Not the plane:
1914 - 4 Door Dodge Touring
This is the plane:
Fords 1925 Tri-Plane
11/11/1940 – The first Jeep
1940 Jeeps
11/12/1908 – GM takes over Oldsmobile.
11/25/1844 – Mr. Benz was more in Karlsruhe, Germany (Been there, the wine is excellent, the beer is better and the food is OUTSTANDING!)
11/26/1966 -The DeTomaso Mangusta debuts
1966 DeTomaso Mangusta
11/27/1870 – Joe Mach’s birthday. Yeah…the guy that started MAC trucks. The company started when Joe and his brothers purchased a carriage and wagon company in Brooklyn, N.Y. The first vehicle they produced was a tour bus. (1900) Next up was rail cars and locomotives. At the time they used the name Manhattan. Somewhere between 1910 and 1911 the name changed to Mack at about that time the Mack brothers bought a truck company. Oh..in case you are wonder the Bulldog became their logo in 1922 and the name was changed to MACK Truck. When I was a very young, we called all tractor-trailer Mack Trucks.
1910 Mack Hook and Latter firetrucks
New Auto Factoid format.
The Ford Mustang sold 419,000 cars in the its first 12 months on the marked. That number trumped the 417,000 cars set by the 1960………………Ford Falcon!!!!
