Car Design – 2 Pipes or 1?

I often have several articles going at once.  However, since I don’t to this for a living (yet) daily activities, like driving to work, often give me ideas for a quick blogging episode, the other article wait.

Like the other day after work, which was a good one at the old salt mine, a rarity, I was headed to my work out session with my “very understanding” better half and the car in front of me made think of a particular feature of  a car’s design.

In this case I need to give you an insight into some of the things that go on in my head while driving.–Don’t worry this is the PG version–.  The most important need is to be very diligent as to notice other corvettes..got to keep the wave alive…”  missing  a wave is a violation of the corvette code. (Yeah…really…and you thought all you had to do while driving a Corvette keep an eye out for ‘smokey’.)  Second most important thing is to keep an eye out for old smokey.  Then there’s the sizing up of your road-mates as you are stopped at a red light.   After those serious tasks,  I look at the tail end of the cars around me to see if they are two pipes or one and of course size (exhaust envy – it’s real!!). One tail pipe means it is a “girlie man’s” car and two or more is of course the opposite.   Hey… it passes the time while sitting in traffic.

Normally, I check out cars of all types for tailpipes,  Honda, VW, all the domestic  brands and models.  Most only have one and some have the bumper designed for two but still come up short one pipe.

So today, I’m sitting a traffic light at Broadway and Aviation Highway behind a Saturn Overlook cross-over vehicle.  Habit takes over and I noticed that there was only tail pipe – girl’s car.  As I looked closer the rear end, I noticed what appeared to be a factory designed space for a second tail pipe.  But the gap wasn’t just a mere indent where the second should have been.  It was a very wide space.  The design of that of its exhaust system on the end has muffler that looks like  an over sized World War II canteen.  The tailpipe sticks out of this elongated canteen at about a 70 degree angle.  The muffler is exposed and hides the rear suspension.  In the picture below you can see the dual exhaust.  

Saturn Outlook with Dual exhaust

   Now picture the left one removed without the muffler.  What you’d see is a cut out and the left independent suspension structure. Why not close that off?  The real reason is cost of having two different rear bumpers’

Below is a picture of a 2008 Outlook and you can see the exposed rear suspension.

Exposed suspension

 So while you are driving, look at the backend of the car in front of you.  You’ll see that Honda Civic with a place for a second the extra exhaust pipe and you’ll think…”Really? It was designed for a dual exhaust?

Thanks for reading.

Tim

US or Metric Thread Guage

These are handy to have around.

 

Bolt Depot - Thread Guage

So handy, I’d like  to give a couple away.

For next 3 individuals that sign up for my feed and drop me a comment.  I’ll send one of to you.

I’ll be notified of your subscription via WordPress.  In you comment include whether you need the Metric of  U.S. version.

 

Thanks for reading.

Tim

Barrett-Jackson Scottsdale, AZ

Headed there this weekend.  Look for pics and posts coming up.

 

Tim

Engine Mini Series – Chevy’s 283 Part 3

This is the part of the engine series where I list the uses for the power plant.  The 283, as I mentioned, carried Chevy engines to the next level, by being the first engine that car manufacturers were able to coax out the same horsepower as the displacement.

From 1957 (its inception) to 1959 the 283 was the base model V8 for nearly all Chevys, coming in a 2 and 4 barrel versions with the 4 barrel being the main power plant for the Corvette.  In 1958 the 4 barrel version was dubbed the Super Turbo Fire with 220-230 hp with 9.5:1 heads.   (Toss that name in with other versions like the 348 Turbo Thrust and the Super Turbo Thrust which sported 3 two barrel carbs.)  The other premier engine during that period was of course the FI used in the Corvette with 9.5:1 and 10.0:1 compression.

The 283 Super Turbo Fire

1960-1961 saw the base 283 drop to a 2 barrel and muster just 185 hp.  The bright spots were engines used only in the Corvette, the dual quad and the FI engines.  1961 also saw the 283 go MARINE – nope not joining that elite military branch but rather Chris-Craft the boat builder, sealed it tight and give a duty on their Cavalier Cruiser vessel.

Marine 283 for Chris Craft Cavalier Cruiser

Not much changed in 1962-1963, at least nothing very exciting.  Chevy dropped the dual quad as an option (although I bet you could still get it done) and the 283 dropped in hp to 170 and as was no longer an option for the Corvette, but was added to the Impala.

As perhaps a last chance to breathe some life into 283 Chevy gave it a bump in hp to 195 and it found a new home in the new Chevy II in 1964 and 1965 a 4V was added give the iron 220 hp and another new home the ’65 Chevelle.

But that couldn’t save the 283, it was time for Chevy to move on and 1966 was its final year.  It served as the base V8 that year as an option for the Chevy II and Chevelle and the other Chevy sedan’s, like my 1966 Impala.

Although it seems like I give this a quick pass (not a long list of models) the 283 served nearly all models of Chevy from 1957 to 1966, listing them all would be, well ..repetitive . Interesting enough it never crossed over to the other GM brands.  But it did make it into the Canada made Studebaker cars  in 1965 and 1966.

During the it’s life span the 283 was offered with every transmission available for that year. From the torque glide to the power glide automatic transmissions and even a few 3 and 4 speed manuals.  Additionally, I was surprised to find that it was offered with air suspension with some automatic.

Did the 283 really die? Nope it received the cam from the 327 and became Chevy’s 307!!

Notable:

–          The 327 followed the 283 and although it was an entirely hunk of iron, to keep cost down Chevy used some 283 components initially.

–          GM’s RPO 579E option on the 283.  579E was called the Air Box.  It was perhaps the first production cold air induction system(at least for Chevy). It consisted of a plenum box mounted on the fender well of the driver’s side.  The box was fitted to an opening in the bulkhead next to the radiator with an air filter inside.  The duck work ran to the fuelies injection unit. Records indicate that there were only 43 produced in 1957.

1957 Corvette AirBox

–          Corvette Fuelies had a reputation for hard starts and finicky operation and many were replaced with the standard carburetor  (1957)…Flash Forward the 1984 Corvette Crossfire (fuel injected) (Of which I was a previous owner) suffered from finicky operating and some were replaced with carburetor set ups.

I hope you enjoyed this little bit of engine history and as always, thanks for reading.

The correct should be – the 283 received the “crank” from the 327 (not the cam) and became the 307.

Thanks.

Tim

Tim

Auto Factoid 2011-2 Chevy Engines

1965 – 1966  Chevy’s mainstay V8 the 283 was used in several Studebaker models build in Canada.

 

1966 Studebaker Cruiser

1966 Studebaker with Chevy’s 283

Chris-Craft boat manufacturer used the 283 in their water boats.

 

 

Marine 283 for Chris Craft Cavalier Cruiser

Chris-Craft Used Chevy’s 283

Thanks for reading.

Tim

Auto Factoids 2011-1 Corvette Fuelies RPO 5789E

1957 – 1958  saw the use of the New 283 engine in Chevy‘s including the Corvette.

The Corvette was fitted with the Rochester RamJet and RAM’s horn intake as the RPO Code 579D.  But recently during some research I read that there was another modification.

It was called the Air Box Option, RPO 579E and it was perhaps the first production cold air induction system(at least for Chevy).

It consisted of a plenum box mounted on the fender well of the driver’s side.  The box was fitted to an opening in the bulkhead next to the radiator with an air filter inside.  The duck work ran to the fuelies injection unit.

Records indicate that there were only 43 produced in 1957.

 

1957 Corvette AirBox

Thanks for Reading.

Tim

 

Engine Mini Series – Chevy’s 283 Prt 2

Oh yes, believe it or not, the 283 put the Corvette at the cutting edge of performance in 1957, fitted with the RamJet FI (fuel injection) system (“fuelie” was the gearhead term for that).  In 1958 the 283 was the base engine for the Corvette, but the 283 that use to put on 283 hp was tuned to create an even 290 hp. If that wasn’t enough for you (of course it wasn’t enough, two words that should never be heard together ‘enough’ and ‘horsepower’…unless…the word ‘not’ precedes them).  The RamJet FI was an available option RPO 579D.

Additional configurations were dual four barrel carbs that produced 270 hp, they were either Rochester or Carter AFB.  The cam was changed in 1958 to give 0.398 inches of lift, improvements made to get more oil to the lifters and the exhaust manifold was reworked, called the Ram Horn’s manifold.  There was a change in how the 283 was mounted.  Chevy used the 3 point system with a mount on each side and one at the rear of the engine at the transmission.

Intake manifold for the 283 Double Quad

Dual Quad set up on a 283

In 1961 the FI jumped the engines’ horsepower to 315.  (Hey, the base corvette in 2007 was 400 hp.) The FI wasn’t the only improvement for the 283 in 1961.  It was treated with a set of solid lifter, improved heads and hydraulic cam which helped the block rich 315 hp, easily.  This would be as far as the 283 would go in horsepower – in production.  1961 was also the last time the dual four barrel carbs were available as an optional configuration.

By 1962 the 283 was replaces by an entirely new engine the 327 (that’s another mini series) as the premier Chevy small block.  The 283 was dropped from the a power plant for the Corvette to a base engine for Chevy’s passenger and used from 1963 to 1964.  Its horsepower dropped to 170 and 195 for two configurations.  A small bright was a four barrel configuration for 1965-67 that produced 220 hp. (That was the configuration of my 1966 Impala convertible.)

Of note is the use of the 283 in Chevy’s light trucks with a two barrel configuration for most of the models in 1958 to 1962.  It produced only 160 horsepower.  For the 1963 to 1967 light truck models the hp was increased to 175.

1967 was the last year for the historic 283.

 

1966 Chevy Impala

 

Coming up next a recap of the uses of the 283.

Thanks for reading.

Tim

Happy New Year and Legal Notice

Happy New Year.

Unfortunately I have to start the year out with a legal notice.  It seems that my writings are so inspiring(…ok…stop laughing!!!) that a few sites have decided that they would use them on their sites in total, placing ads in the middle for their profit and not requesting permission.

I enjoy writing my blog and I do it to share experiences and social interaction.

If you like it, great!!

If you’d like to share links, I’m all for it

If you want to post entire articles ask permission and I’ll send you my list of requirements for accomplishing this.

If you want to use my articles and place and in the articles, we need to talk first.

 

Thanks for reading.

Tim

 

 

 

Auto Factoid for the 2010

Well  Christmas is but a couple of days away and the 2011 is knocking on the door.

Here is the last of the Auto Factoids for 2010.

Enjoy.  Merry Christmas or what every holiday you celebrate and a very prosperous new year.

12/18/1970 – Lee Iacocca becomes President of Ford.

25 years before that on 12/21/1945 – Henry Ford II was named President of Ford

12/20/1868 Mr. Firestone was born in Ohio (Tires)

12/22/1900 The first Mercedes is built by Daimler

Perhaps my Favorite – on Christmas in 1878 Louis Chevrolet was born.

One of my least favorite Ford products showed up the day after Christmas in 1985.  Ford debuted the Taurus and Sable (a Mercury)

Oh..nothing says “buy me” like the Taurus and Sable…look!!!!

1985 Sable or Taurus?

1985 Taurus or Sable..can you tell them apart?? Do you care?

And to finish off the year Charlie Goodyear was born in Connecticut 12/29/1800  (yeah..people blimp guy!!!  and some of the best racing tires available)

Thank you for ready and drop me a note with what’s up with your 2011 car resolutions!!!

Tim

Mustang Carpeting – Who knew!!??!

As part of the mods and upgrades for my 70 Mustang,  I plan on replacing all the carpet.  Before I do that however, I’m going to lay down some heat and sound proofing (but that is another post).

As I start project planning, I’m  looking around for parts and materials, as well as any helpful hints. (If you have any at any time, drop me a comment.)  Although certain portions of the restro-mod will have to be done together, like carb and intake or heads and cam (yes I’m all four will be done at the same time), many can be accomplished separately, like adding the  heat/sound proofing and the carpeting, before upholstery of the seats.  In the Mustang getting the seats out are easy enough (keep in mind my goal is to not have the car tied up too long between stages) so replacing the seats after the carpet installation, isn’t a problem.

As a reminder, the mods will be done in adherence to budget, time and events. So there maybe a need to move between different phases to accommodate either 3 of those factors.

O.K., so where was I, oh yeah..carpet shopping.

As I looking on-line for the best place for ordering carpeting, began to notice a lot of choices.  I start thinking “I’m going to have call up on deck my personal award-winning interior designer (that would be my wife – by profession…no not wife by profession although I’m sure thinks it’s her 3rd career, but Interior Designer by profession).   Here is a little bit of what I found:

Plush Cut Pile

Ultra-Plush Cut Pile

Neon Cut Pile

100% Nylon Loop

I’m thinking, “holy cow!!!…What the heck is this?!!  Ultra-Plush Cut Pile?  I’m not building a ’60 Love Van!!!  Oh it gets better..yeah.. you guessed it samples!!!!!

 

Misty Gray

BuckSkin

My favorite - Cinnabar

 

Oh..come on!!!  Cinnabar!!!!  Really!!??  Um..yup.  Oh and there were many more, like Medium Gray and Silver Mist and Nutmeg and Fire Thorn!!!! I’m not kidding.

So I’m looking round to make sure know one’s looking over my shoulder (as I’m doing this over my lunch at work..on my personal smart phone…just in case “they” are reading!!!)  All the time I thinking…”It’s black..all I know is that it’s black!”

Who knew that there was that much to look at?  Not this Average Guy.

Luckily I found this snippet on one site and it all became clear:

Plush Cut Pile

Our nylon cut pile is constructed from 100% first quality yarn and is similar to what is found in most cars since 1974. It is tufted on a 1/8 gauge machine with 14 ounces of yarn per square yard. It is dyed using the finest dyes available and tested for ozone humidity fading & light fastness.

Ultra-Plush Cut Pile

This carpet is a super plush upgrade to our standard Cut Pile. A 100% nylon cut pile manufactured with over 40% more nylon fiber than our standard cut pile. It is dyed using the finest dyes available and tested for ozone humidity fading & light fastness.

Ok..still not sure here!!!

Neon Cut Pile

Our Neon Cut Pile colors are a great look if you want to make a statement! Although these are not stock colors, they would be appropriate for all applications. There is an additional 15% charge for all applications made with Neon Cut Pile.

What…not stock colors!!!??!!!   What?  Are you sure that is color

wasn’t stock?   It’s Pink!!!!

And the clouds parted and it all became clear.  The very last one was this:

 

100% Nylon Loop

A 100% nylon loop. This material is appropriate for pre-1975 applications only, and was the original type construction used in 1969-1973 Mustangs.

And it came in …………..Black!!!”

Thanks for reading

Tim