From time to time I check out a product that I hear about, in this case, from a repetitive mail from Griot’s garage. This is a catalog of sorts, with a lot of merchandise and everything you need to spruce up your ride.
Thier “Long Lasting Tire Dressing” is the first item I’ve tried.
If you recall I did a review a while back on a tire gel here is the link: ” Like and Don’t Like – Products (Tire Gel) and Tools (Thread Chasers)” http://wp.me/pKHNM-aJ
Now before we start, the bottle you see in the video has instructions and to be fair, I’ll give you any variations.
The direction say, roughly, clean the tire, apply with application pad and that a light application will give you a shine and subsequent will increase the luster. Not much there to go on.
Now you need to know that I applied the dressing with an old sock. Most manufactures always try to sell something extra and kt, which is an “applicator”, the magic potion and a terry cloth/micro fiber towel. I normally don’t go for that sales pitch. So that was the only deviation.
A couple more variables:
1. The dressing was stored in my garage. The temperature in there today was about 105 degrees. I applied the dressing while the car was in the garage.
2. The temp outside was about 108.
3. As you will see my Corvette’s tires have small sidewalls and a lot of small raised text and logo.
Ok so here are a couple before pics:
Before, notice the off-color
More of the discolor and you can see there isn't must sidewall.
After removing the seat track I had to remove the seat stops.
There are two and easily removed.
Next I started removing the upholstery wire. These pliers hook inside the wire and separate them for removal.
Removal
Here are the wires removed. They can be reused if you want to straighten them out.
Wires
Mostly removed.
Part way off however one small deal to handle
Thinking I was on the down hill side with the removal of the old upholstery, I ran into……the …..tuck!!! This consisted of a wire running through a cloth sleeve and the wire is attached to the springs with the hog wire.
Top Arrow is the cloth sleeve with the wire running through it. Bottom arrow is the hog wire crimped to the springs underneath.
Basically the tuck is how they separate the bottom of the seat and the cushions edges, which with vinyl that helps keeps you backside in the seat during those high-speed maneuvers.
Ok, this was the learning seat. I was too busy learning to do too much photography so I’ll to more with the back to this seat and the next.
BUT…………………………..here is my very first seat bottom..completed.
Sorry it’s been more than a couple days…a week plus actually. But hey, it 115 degrees in my garage.
So I removed the seat and inspected the underside.
Again this was my first upholstery job, ever. So removal of the old upholstery on this first seat was a learning experience so I didn’t get too many shots.
Here is a shot of the seat out of the car.
Seat Out
You have to remove the plastic covers for the hinges and the rest of the hardware to separate the bottom from the back.
Just a couple of screws to remove the covers, hinges and hardware
Here is the underside of the seat with the track hardware still attached.
Back removed the track still in place.
The track is remove with 4 star bolts. Be careful use the proper socket, I happened to have just purchased a huge set of tools (a bit more the ‘average guy’ might have) that had the necessary socket set. If you don’t have those, find one of those universal sockets that ‘form’ to bolt.
4 star bolts hold the track to the frame of the seat bottom
There is a lot of emphasis on numbers for production when it comes to collector cars and I get that, who wouldn’t what a low product something or other.
So I got to thinking about production numbers and thought it would be interesting post some up from time to time.
Now in 1902 there weren’t many cars being produced but there were 8 makers.
I have a co-worker who from time to time has mentioned his Pontiac project and we’ve ‘bench restored’ a few times. But I’d never actually saw this car , nearly a picture. But thanks to our first real rain here in Southern AZ since last year I think, and the fact that we don’t do our monsoon season any other way than “harsh” my co-worker’s (we’ll call him ‘Mike’…’cause that’s actually his name) neighbor had a tree that suffered enough wind damage it and to be taken down. So Mike had to move the car, parked it behind his daily driver. Got up this morning and decied..heck, I’ll drive it to work.
And that’s how I got the pic of the 1949 Pontiac Silver Streak Delivery Van, all original and get this…..his family is the only owner the beauty every had. His grand father purchased it new. More to come on this one but here are some pics.
1949 Pontiac Delivery Van
Back Side of the '49 Silver Streak Delivery Van Pontiac style.
OK after all these years, after the car was gone. I stopped by the house. I was met by Al, short for Albert, not Alan, as Al informed me.
I told him that I had always wanted to check on the Grande and he informed I was a bit late. He said he didn’t mind answers a few questions.
So I asked Al how got the car and he said he bought it back in 1972 from some guy. “It was a nice car with an automatic.” Of course my next question was what was under the hood and he said ‘nothing’. “Took it out about 10 years ago and parked on the side of the house.” He told me he never got the engine fixed, ” ’cause it ‘cost too much.” He ended up letting the guy that did some work on it keep. “Ya know, it might have been a 302.” He said he didn’t really know want to do with the body and just ended up hanging on to it.
So I asked him where the car end up, hoping it was sent out to be restored. He said there was this guy from Texas that would stop by every now and then and ask if it was for sale. He drives large pick up and always has an empty trailer attached. This same guy that has stopped by a co-worker of mine, who has her son’s 70 Monte Carlo and her daughter’s 1969 Camaro sitting under her car port – waiting for some TLC and try’s to convince her that she should sell them to him. She chases him off each time, but he’ll swing by a few months later.
A couple of weeks ago, Texas dude, stops by Al’s home and Al decided to get the Grande out of the yard and sold the man from Texas.
We talked a bit longer about my 1970 Mustang coupe and I showed him a couple of pics on my phone and then thanked him for his time.
For the Mustang the studs pass through the track and the nuts are under the car so a little space is need. Since most average guy’s don’t have a lift in their home garage, so I pull out the trusty 2 ton floor jack and a jack stand.
As most Mustang owners know, they were built with subframes. When jacking up the car with a floor jack place it on the frame, or use the standard scissor jack that attached to the seam at the rocker panel. Either way once it’s in the air, DO NOT FORGET to put the jack stand under the car. Yes it actually takes longer to do the set up then to remove the bolts…but take the time to be save.
2 Ton Floor Jack
Floor pan plug that protect the bolts and studs.
These plugs pry out very easily. I was able to get them out with just my fingers. Once they are removed you’ll have access to the nut. The distance between the opening and the nut requires an extension and the length of the stud requires a deep socket. These were 1/2″. The Mustang was raised in Arizona (get it? First reader to drop a comment explaining “get it” wins a DVD.) and all the plugs are in place. This kept all the road grime and what not off the studs and nuts, they separated easily.
When you are done you should have this many parts.
When I purchased the Mustang I was told that the upholstery was replaced at some point. (Keep that in mind for later as well.)
As you can see in the video I wasn’t able to get the seat out of the car. I initially I figured it was because I couldn’t pull out level enough for the studs to clear the holes due to the fact that I was holding the camera. However, after putting it down I still shouldn’t get the seat out. So I climbed back under the car and found that there was a second nut on the right rear stud. I’m guess it was doubled up, when the last installer wasn’t sure whether they already but one on? And of course you can see by the previous picture that those two nuts not the same as the others.
Part III will be coming up in a day or so.
Thanks for reading.
Tim
I know, I have a lot of work scheduled for the Mustang. This includes interior work and yes maybe doing it all at once would be a good idea. But I drive it a couple of times a week and the seat is getting worse. So I decided it needed to be fixed.
The kit is from TMI and I think I purchased it from a Mustang parts dealer, but I don’t recall which one. Here’s a couple of videos on it.
What I noticed is the black piping. I know that the car was re-upholstered before I purchased it, so I’m guessing that this was not original, at least they don’t make them in the reproduction world.
