While trying to warn a real life coyote of his ‘rapid’ approach, Bill’s 1968 Road Runner (#ProjectBeepBeep) failed to issue the famous BeepBeep, or was that just part the car’s instinctive DNA based response to coyotes in general? Either way Bill tackles the problem. Here’s a shot of the horn. More coming up …
Ready for some more #ProjectBeepBeep? Bill takes you through a few tips for restoring your B-Body door panels. Take a look: Great stuff!!! Thanks Bill!!! Have a few Mopar tips – Post them up or drop me a note @ agcarestoration@cox.net and we get you video/tip posted on the site. Thanks for reading Tim Introducing …
Bill takes a look at MOPAR Body Bumper Kit for #ProjectBeepBeep and shows a common mistake made when a car is painted. Bill is correct that the bumper are painted over show an oversight that might just tank the value of your car. I grew up working in my Dad’s body …
Welcome back to #ProjectBeepBeep. Bill is working on finishing up the brake conversion. Here is a progress update. Note: I forgot to add the credits for these videos: Starring Bill B as himself; BeepBeep as ’68 Road Runner; Wild E. Coyote in effigy Camera Production; Mrs. Bill B and SamB Editing Tim …
Welcome back to #ProjectBeepBeep. Thanks for checking in on the progress of Bill’s 1968 Plymouth Road Runner. If you recall mixed in with some brake updates, Bill mentioned that he had sent out the circuit board for a restored. Here is an update on the status of the dash. Next up an …
Well it has been a while since I’ve updated readers on #ProjectSportsRoof and frankly there hasn’t been a lot going on.
As the regular readers know I do all the work I can on my car, when practical. This work happens in my driveway, which unfortunately has a rather steep slope.
You’ve seen the videos of my work pulling out the engine and the transmission and putting the engine back in and attempting to put the transmission back in.
I few weeks ago, after suffering from a huge bout of guilt for not working the Mustang, I attempted one more time to get the transmission reattached to the engine.
This endeavor, required me to put the car up a lot higher than normal on the stands, to get enough room to maneuver the trans and the transmission jack around. this was a huge mistake. After a few tries I decided to pull the transmission back out for under the car and wait for some help later in the week.
Everything went fine and the transmission was safely strapped to the transmission jack and rolled back into the garage. Since the car was lifted higher for the failed attempt, I decided to lower it back on to the ground. As I lifted the car with my floor jack, so I could remove one stand one of the remaining stands slipped from its place and the car dropped about 5″ on to the tires. This didn’t seem to be to dramatic of a fall until I noticed that the motor mounts had separate (broke to be frank).
That was depressing, to say the least and another set back. Of course this depression was compounded by the fact that I had very limited free time coming up to work on the car. I am a full-time Junior High teacher and I had just signed on to coach our boy’s basketball team which was a lot of fun (we when 10 -2 for the season) and very time-consuming.
I purchased the motor mounts and was attempting to schedule a couple of relatives to help out. That proved difficult.
So a relative mentioned a successful automotive shop that was opening a new location here in Tucson and I contacted them to see they wanted to tackle the engine and transmission re-install, build a custom drive shaft and add headers and exhaust. They looked it over and we agreed on the cost estimate.
So off she goes to get the complete drive training straighten out and hopefully back on the road soon.
There is still a lot of work to be done and as I get ready for my summer break from teaching, I should be able to but more time into it!!!
I have a lot more coming up on #ProjectBeepBeep as well.
Welcome back to #ProjectSportsRoof. I run my car projects much like I run my IT projects. You always have to know where to start and know the end game. As with any project that isn’t being built from scratch, in other word, you have to work with what you’ve got, …
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
As I posted before, after a vigorous (not read ‘desperate’) I finally found my next personal project. The 1973 Mustang Sports Roof Fastback is what I settled on. Now we start the project that has been dubbed #ProjectSportsRoof (yes I find it necessary to use the ‘hash’). 1973 Mustang Color …
Ok so these were suppose to kick off while I’m over here in Italy, but they failed to post up, so I’m taking a few minutes to fix that. Oh well as long as I’m typing, here is my favorite Italian road sign: Welcome back to Project Sports Roof (#ProjectSportsRoof). We stripped …
In these next two videos, you’ll see just how ‘off’ these fenders are in some areas and surprisingly how well they fit in other areas. If you have an experience or a hit for anyone taking on this part of a restoration – drop a comment here and we’ll share them. https://youtu.be/Ga9EHbDpSfg https://youtu.be/FBKs7EG4kK0 Thanks …
Well win some and you lose some. If you’ve seen my other posts related the replacement of the points and condenser for the 351C you’ll notice that I gave conversion high marks. This was all based on the years of use I got out of the conversion I did on …
Thanks for checking on #ProjectSportsRoof. So here is the last set of initial questions. Here is an image of the current set up: Any diagram I find has the hose vacuum from the Distr going to the Valve assy. The Valve assy has nothing attached which is located on the front …
While trying to warn a real life coyote of his ‘rapid’ approach, Bill’s 1968 Road Runner (#ProjectBeepBeep) failed to issue the famous BeepBeep, or was that just part the car’s instinctive DNA based response to coyotes in general?
Either way Bill tackles the problem.
Here’s a shot of the horn.
More coming up on #ProjectBeepBeep and #ProjectSportsRoof.
Thanks for following our projects and find us on FaceBook @ www.facebook.com/AGCarRestoration/
I’d like you to take a look at one of my constant readers classic muscle car. First let me say that Bill has been an a long quest to find a car to replace this car: Back in the day. It was a long search with lots of phone calls with many …
1968 Ply Road RunnerProject BeepBeep Welcome back to #ProjectBeepBeep. Bill is looking at the brakes and gets some professional assistance to help him make a crucial decision. You know if you’ve got a lot of GO…you need a lot STOP. It not an easy decision to alter a car’s originality, especially …
Thanks for checking back in on #ProjectBeepBeep. Having made the decision to convert the front brakes from shoe to disc Bill gets started with this major project for #ProjectBeepBeep. He went with a kit from Dr. Diff and here’s a brief look at some of the contents. Nice shiny new rotors!! Spindle …
Spend a few hours on this 2017 Labor Day, laboring over #ProjectSportsRoof and I wish that labor paid a bit more dividends.
The goal was to mate the transmission back to the engine but unfortunately that just wasn’t going to happen today. The engine is set back a bit too far and tilted (on purpose). Problem is if I bolted them up the engine hoist would be able to lift the engine and trans due to the height I needed the car to work on the transmission.
So I pulled the transmission out from under car and placed its wheels back on the concrete.
It was a major effort to get the car up high enough to get the transmission out. I pushed the boundaries of safety with a floor jack and a couple of jack-stand.
As I stated in the video I may just take it down the street and have them get that straightened out for me.
Welcome back to #ProjectSportsRoof. I run my car projects much like I run my IT projects. You always have to know where to start and know the end game. As with any project that isn’t being built from scratch, in other word, you have to work with what you’ve got, …
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
This is the wrap up on the compression testing for the 1973 Mustang w/ a 1972 351 Cleveland power plant. You’ll might have notices that I referred to the remote tester, which is my code for remote starter…yeah…that’s it!!! All of these tests were dry test and I should have done a …
I’d like you to take a look at one of my constant readers classic muscle car. First let me say that Bill has been an a long quest to find a car to replace this car: Back in the day. It was a long search with lots of phone calls with many …
Ready for some more #ProjectBeepBeep4? Bill takes you through a few tips for restoring your B-Body door panels. Take a look: Great stuff!!! Thanks Bill!!! Have a few Mopar tips – Post them up or drop me a note @ agcarestoration@cox.net and we get you video/tip posted on the site. Thanks for reading Tim Introducing …
Bill takes a look at MOPAR Body Bumper Kit for #ProjectBeepBeep5 and shows a common mistake made when a car is painted. Bill is correct that the bumper are painted over show an oversight that might just tank the value of your car. I grew up working in my Dad’s body …
Welcome back to #ProjectBeepBeep6. Bill is working on finishing up the brake conversion. Here is a progress update. Note: I forgot to add the credits for these videos: Starring Bill B as himself; BeepBeep as ’68 Road Runner; Wild E. Coyote in effigy Camera Production; Mrs. Bill B and SamB Editing Tim …
Welcome back to the #ProjectBeepBeep. We are still following Bill’s progress on the front disc brake conversion for his 68 Plymouth Road Runner.
Did I say this is the final chapter? Well….
Sometimes during a project you just can’t afford the time to do a video, especially when you have a friend coming by to help out. Lets have Bill tell you how it all ended:
“I had to call in an expert; fellow I work with is a Mechanical Engineer and used to work as a Porsche/BMW mechanic before and during college. Together we got the wheels on the ground in about two hours. He recommended a last-ditch effort with the brake lines; we tightened all lines until the tube nuts were deformed. Also found an off center flare on one of the brake lines and he had a machine that fabricated the new line. Difficult to bleed; we bled the system 11 times (I counted) and went through lots of brake fluid (almost two quarts).
Took BeepBeep to the MOPAR show at Larry Miller Dodge almost immediately after getting the wheels on the ground! Car stops on a dime and gives you nine cents change. Don’t miss power assist at all. This car will STOP!
Check it out:
I need an alignment next, but otherwise I really have no other problems to report. Everything working; oil PSI is 35 at idle, 55 at running down the road, and temp was a tick under 195F all day long.
Time to enjoy this ride!”
Bill, thanks for the all the video and the tips you given the reader!
Looking forward to your next ‘little’ project on BeepBeep.
I’d like you to take a look at one of my constant readers classic muscle car. First let me say that Bill has been an a long quest to find a car to replace this car: Back in the day. It was a long search with lots of phone calls with many …
1968 Ply Road RunnerProject BeepBeep Welcome back to #ProjectBeepBeep. Bill is looking at the brakes and gets some professional assistance to help him make a crucial decision. You know if you’ve got a lot of GO…you need a lot STOP. It not an easy decision to alter a car’s originality, especially …
Thanks for checking back in on #ProjectBeepBeep. Having made the decision to convert the front brakes from shoe to disc Bill gets started with this major project for #ProjectBeepBeep. He went with a kit from Dr. Diff and here’s a brief look at some of the contents. Nice shiny new rotors!! Spindle …
Ready for some more #ProjectBeepBeep? Bill takes you through a few tips for restoring your B-Body door panels. Take a look: Great stuff!!! Thanks Bill!!! Have a few Mopar tips – Post them up or drop me a note @ agcarestoration@cox.net and we get you video/tip posted on the site. Thanks for reading Tim Introducing …
Welcome back to #ProjectBeepBeep. Bill is working on finishing up the brake conversion. Here is a progress update. Note: I forgot to add the credits for these videos: Starring Bill B as himself; BeepBeep as ’68 Road Runner; Wild E. Coyote in effigy Camera Production; Mrs. Bill B and SamB Editing Tim …
Welcome back to #ProjectBeepBeep. Thanks for checking in on the progress of Bill’s 1968 Plymouth Road Runner. If you recall mixed in with some brake updates, Bill mentioned that he had sent out the circuit board for a restored. Here is an update on the status of the dash. Next up an …
Welcome back to #ProjectSportsRoof. I’m finishing the re-positioned shifting rod above the transmission’s cross member.
Next I’ll need to go top side and give the selector a try. If that is working properly, hitting the proper gears I can spin the torque converter and properly torque its connection to the flex plate.
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
I’ve done all the clean up and all the adjustments necessary to get a good reading on the health of the ’72 351C engine in my 1973 Mustang. The next step is to check the compression. First up was to warm the car a bit and then pull the plugs. Here’s what the …
This is the wrap up on the compression testing for the 1973 Mustang w/ a 1972 351 Cleveland power plant. You’ll might have notices that I referred to the remote tester, which is my code for remote starter…yeah…that’s it!!! All of these tests were dry test and I should have done a …
It’s past time to get it in gear and get the transmission back in shape to get the power from the newly bored out .040 351 Cleveland to the rear wheels.
With the help of my nephew Josh (thanks Josh!!) the transmission was effortlessly (ha) in to place…almost.
Here a more current status video.
All Bolted in.
Now that it’s all bolted in place, I need to work on the getting the kick down road back in place. That’s coming up next on #ProjectSportsRoof.
Welcome back to #ProjectSportsRoof. I run my car projects much like I run my IT projects. You always have to know where to start and know the end game. As with any project that isn’t being built from scratch, in other word, you have to work with what you’ve got, …
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
Bill continues with his march toward a complete brake system replacement for #ProjectBeepBeep his 68 Plymouth Road Runner.
Here is the Bill’s update.
There is more coming on the #ProjectBeepBeep and #ProjectSportRoof.
Keep an eye out for dates for the new Average Guys’ Car Restoration Live Event on Face Book AG Car Restoration FB . We’ll touch on car news, new productions, muscle and collectible car talk. You’ll get to call in and add to the conversation.
I’d like you to take a look at one of my constant readers classic muscle car. First let me say that Bill has been an a long quest to find a car to replace this car: Back in the day. It was a long search with lots of phone calls with many …
1968 Ply Road RunnerProject BeepBeep Welcome back to #ProjectBeepBeep. Bill is looking at the brakes and gets some professional assistance to help him make a crucial decision. You know if you’ve got a lot of GO…you need a lot STOP. It not an easy decision to alter a car’s originality, especially …
Thanks for checking back in on #ProjectBeepBeep. Having made the decision to convert the front brakes from shoe to disc Bill gets started with this major project for #ProjectBeepBeep. He went with a kit from Dr. Diff and here’s a brief look at some of the contents. Nice shiny new rotors!! Spindle …
Ready for some more #ProjectBeepBeep? Bill takes you through a few tips for restoring your B-Body door panels. Take a look: Great stuff!!! Thanks Bill!!! Have a few Mopar tips – Post them up or drop me a note @ agcarestoration@cox.net and we get you video/tip posted on the site. Thanks for reading Tim Introducing …
I thought I’d take a minute and catch the readers up on #ProjectSportsRoof.
I wanted to touch up some of the engine bay components, horns, vacuum canister and battery tray. I didn’t want to alter some of these too much, I like having the numbers, logos and other info visible, not covered under a several layers of primer and paint. So these items were lightly sanded and then sprayed with primer and black engine paint.
Battery Tray – in the process of being sanded with dremel.
The horns were cleaned up with break cleaner then sanded by hand.
A lot of the paint just came off with the cleaning.
Horn in the process of being sanded.. Note the “LO” and other numbers. My goal is to keep them visible.
A coat of Eastwood Rust Encapsulator and then a primer coated applied – tried to keep the numbers, etc. visible.
A little more sanding and then some paint.
Vacuum Canister
Battery Tray and Horns
I think they came out O.K.
There is a quick video.
Coming up distributor install and transmission update.
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
I’ve done all the clean up and all the adjustments necessary to get a good reading on the health of the ’72 351C engine in my 1973 Mustang. The next step is to check the compression. First up was to warm the car a bit and then pull the plugs. Here’s what the …
This is the wrap up on the compression testing for the 1973 Mustang w/ a 1972 351 Cleveland power plant. You’ll might have notices that I referred to the remote tester, which is my code for remote starter…yeah…that’s it!!! All of these tests were dry test and I should have done a …
