Category Archives: Mustang

#ProjectSportsRoof – Rear Brakes Change of Direction

By | | , , , , , , , ,
1 Comment

Every good saga needs an ending….even if it’s just terminated without a related solution.      

So it is with #ProjectSportsRoof (my ’73 Mustang) brake saga.    This all started when Bill – (#ProjectBeepBeep date) came over to help dial in the carb and timing on my 351 Cleveland.   We discovered brake issues after taking the Mustang couple test drives.  Front brake seemed to be doing all the work.  It was clear that brakes need to be bumped up on the list of things “needing doing”.

Gathering all the parts was easy enough.  As you now know that’s not true, the rear end had been frankenstein’ed and shoes were the main issue.

After thinking it over and I decided to go a different direction.   Since the fronts were disc why not go disc in the back as well. I started hunting around for prices and options.

There is a lot out there in the back of my head was Bill’s fabulous adventure with converting #ProjectBeepBeep to disc.  Prices very and so do configurations.   There is even a set up where you have small set of brake shoes that perform the emergency brake function and the disc brakes.  Like this:

 

There were also those that allowed the disc to handle the emergency braking.

I checked out all brands and all type.  As I was looking a downloaded PDF from  Master Power Brakes, I saw these:

Rear Drum Brake Conversion Kit: Legend Series Deciding to keep drum brakes on the rear of your vehicle is not a bad thing. What is a bad thing is not upgrading them to a system that makes sense. Our rear drum upgrade kit utilizes a large 11 inch drum, all new components and 1-1/8 inch wheel cylinders giving disc brake feel without the expense.

 

I have nothing against drum brake as they function (of course changing  pads is easier then changing shoes).  My 1970 Mustang used them just fine, even at the drag strip:

So read up a little more and decided to go with the Master Power Brakes’

Ford Mustang Rear Drum Brake Conversion Kit for Ford 9″- Legend Series.

Here’s a video:


 

These will bolt (you have to pull the axles) and they are 11″.

One side arrived already.

 

 I think it was a good choice.  I’d love to show you the installation but I’m not.   Pulling the axles is a messy job and outside temps are normally in the 100’s here in So. Az.   It’ll need new seals and bearing, so #ProjectSportsRoof is going into the shop next week.

But don’t worry I have a few posts on the install of the new calipers for the front disc coming up.

Thanks for stopping by!!!

Tim

 

 

 

 

 

#ProjectSportsRoof – Brake Shoes – The Measurements.

By | | , , , , , , , ,
1 Comment

If you stopped by to see a video on measuring for brake shoes, you’ll have to read instead.  I was pretty frustrated at the time and my selection of verbiage would have been Rate R. Sometime a story is best told through pic only.

I’m not inventing something new, merely showing where I went sideways and what I should have done.

For the record, most you know, I went with what the all the parts books said were the proper size, 10 in x 2 in.   Again, I took a quick measurement and it looked to be 10 in.

Here is what I should have done.

Measure the back plate.

yeah….11 inches not 10!

Inside Diameter

I captured my mistake on camera – just wee bit off not 2″ but 1.75″.

These are the measurement I should have taken.

So the story dragged on with the ordering of shoes for a Ford Galaxy – they were huge  and finally finding the 11 in x 1.75 in from a 1973 Bronco.   That was it!! They were the right size….even brought the old shoe with me and matched them at the store. 

Insert huge sigh

I installed them…almost.  Here’s why that didn’t work.

Old shoe is on the top and it’s tapered.

Here is a closer look.

That little bit of taper was key to getting the brake shoe under the shoe retainer washer.

The width of the new brake shoe was too side and forced the washer (times referred to a shoe guide plate) too far out on the pin and left no room for both springs and the auto adjuster.

So my solution failed.  What’s next?  Maybe a different direction for #ProjectSportsRoof?

Thanks for checking back!!

Tim

#SR73

 

 

 

#ProjectSportsRoof – Brake Shoe Consternation!

By | | , , , , , , , ,
1 Comment

Oh well this is crazy…of course it would have been easier if I followed the old adage, measure twice – post once.  I’ll get to that in a minute.

Every one of the parts house and everyone in one of the online forums and Facebook groups (including mine Average Guy’s Car Restorations and Projects) said the rear brake shoes for #ProjectSportsRoof were 10 inch by 2 inch.  Maybe  because that’s what the parts books said it should be so I went with that.  I did a quick measurement of the shoes (not the drums). 

Ordered the 10×2 and went to install them I noticed they seemed too small. I ordered a set from NPD and attempted to put them on, too small.  Called them up and went over it with them.  Together we thought they were just miss packaged.  They comp’ed them and sent me another set.  Check it out:

Those were (of course) the same as the last set.  By chance I thought let me order a set from SummitRacing.  Those too were too small.

Here a quick video:

 


 

Clearly there’s been a swap of some kind. Now if I had taken the measurements and done so thoroughly, I could have saved some frustration.  Taking the shoes back and forth the local parts stores (more then one and more then one time) I found little help.   I will say that CarQuest – which is way across town from my place, were the best at helping me track down the shoe size.   The guys on 3 Facebook groups all were helpful…but I made a mistake there.  I had mocked up the drums you see in the video just to show them the size difference.  Well that led to a lot of post freaking out about the lack of auto adjuster parts – which aren’t necessary, if you don’t mind making the adjustments yourself, when you feel the braking a bit off – NOT RECOMMEND however for general/common drivers and the spring wouldn’t fit…because the shoe were too small to hold them in place I popped any spring that I could get on easily.  As always you’ve a few condescending “experts” that missed the point of the pics/videos but that’s gonna happen on the web.

So the hunt began.  I’ll fill you in on that in the next post and show you the measurements I “SHOULD” have taken.

Thanks for checking in!!

Tim

#ProjectSportsRoof – New Rear Shocks and Spiders get an Eviction Notice.

By | | , , , , , , , , , ,
1 Comment

Welcome back to Average Guys Car Restoration.

Rear shocks required a bit of  “extra” work to install and sadly a few of natures creatures, need to find a new home.  Take a look:

Now I doubt that I’ve impressed upon the spiders to permanently relocate, perhaps with a it of training I can get them to at least clean up the undercarriage a bit.

#ProjectSports Roof now has all new shocks.   There is still so much to do…coming up next brakes and upholstery.

Thanks for stopping by!!

 

Tim

#ProjectBeepBeep Door Hinge Replacement

By | | , , , , , , , , ,
1 Comment
There is nothing easy about lining up new car door hinges. Doors are heavy and getting them aligned is a major undertaking….but Bill’s got a better way.
In this posting. Bill lays out a great process for changing door hinges using his 68 Road runner #ProjectBeepBeep as his patient.
There are a host of tips in this video. A must watch!


 

Bill’s correct, the drivers door hinges on #ProjectSportsRoof are bad.  But now that he has perfected the art of door hanging, I’ll borrow his expertise and this Rest Door Hanger for getting the Mustang’s door perfect!!!

Well protected against damaging the paint

floor jack with cradle removed and door support tool the Steck EZ Rest Door Hanger

Coming up Bill gives a few tips on painting your hinges.

Thanks for stopping by!!

Tim

#ProjectSportsRoof – Vapor Lock – New Carb – CLOSURE

By | | , , , , , , , , ,
1 Comment

I’ve finally put the fuel issues to bed with fuel line insulated, crushed line repaired, fuel pump upgraded and now a new carb.  Through the process I’ve eliminated vapor lock – video proof showed the issue was with the carb float.  Final analysis is that the float was cracked, filled with fuel and failed to control the level of fuel in the bowl.

Now the new carb is 1406 Edelbrock which is a downgrade from 800 CFM to 600 CFM (1413 Edelbrock).   The #ProjectSportsRoof is running well.  However, I don’t think I’ll leave it with the the 600.    The 800 was in bad shape.  Maybe only 60 miles on it, but it sat for too long, with bad fuel and just cleaning it up didn’t work.   Some say the 800 is too much for the 351C but I noticed a difference between the two carb so the 800 it going back for a professional rebuild and it will end up back on the SportsRoof. 

Here is the removal of the 800 and the installation of the 600.

 


There is still a lot coming up on Average Guys Car Restoration. Bill had some hinge work on #ProjectBeepBeep and there a lot more on #ProjectSportsRoof.

Thanks for checking.

Tim

 

#ProjectSportsRoof On Camera Update 06-04-20

By | | , , , , , , , ,
Leave a comment

Here is a quick update on my 73 Mustang (#ProjectSportsRoof, #SR73):

 


 

Lots coming up so check back!

Tim

#ProjectSportsRoof Fuel Issue – Carb Float Adjustment

By | | , , , , , , ,
6 Comments

Well we’ve landed here temporarily with the vapor lock – not series of posts.   Clearly we aren’t having a vapor lock issue and had I set up a camera much earlier I would have seen the issue pretty quickly.  

With fuel spewing out of the carb, which isn’t ideal, we can narrow it down to a carb issue, not a fuel line getting to hot and not a fuel pump issue (but I’m glad I upgraded from the old one).

Here is the video of the float adjustment:

 


 

So my options at this point is to have carb rebuild or down size to 600CFM Edelbrock.

What would you do?   Drop a not and let me know.

Thanks for checking in #ProjectSportsRoof.

Tim

#ProjectSportsRoof Vapor Lock or Not – NOT!!

By | | , , , , , , , , , ,
2 Comments

Welcome back to #ProjectSportsRoof, my RARE (snicker) 1973 SportsRoof Mustang (#SR73).

I’m catching up on the fuel issue with my 351 Cleveland.

I didn’t notice but in the last posting at the very end of the video when I’m attempting to start the car there is an issue with the carb.  I totally didn’t catch it at the time nor did I see it in the video. 

I really struggled with trying get a video on the removal and installation of the new Speedmaster Fuel pump.  One of the hazards of working on a ‘semi-cool’ car like my Mustang – outside in the driveway, is that neighbors love to peek in on the status and of course chat.  The installation had some many interruptions that the video was choppy and salvageable.  I had some misgivings about the Speedmaster pump, more exactly the lack of support – no instructions for adjusting the configuration(which required disassembly to accommodate different applications and no specs on the fittings required).  I did managed to get  few tips and the after math.  Here’s what it looked like:

 

 


So clearly it was not the fuel pump nor was it vapor lock but in fact it was the floats. I tackle the those in next post!

 

Thanks for checking in on #ProjectSportsRoof (#SR73).

Tim

 

 

 

#ProjectSportsRoof – Fuel System Diagram

By | | , , , , , , , , , ,
2 Comments

As I sorted out the fuel issues with my ’73 Mustang (#ProjectSportsRoof) (#SR73)  I was asked about the fuel system and what I used for reference.

I have all the manuals and specs with diagrams  but the best I’ve found is from a a sales catalog.   National Parts Depot has it laid out and labeled.  You’ll have to excuse their SKU numbers but it’s a great resource.

Check it out:   – OH I will have an update on the fuel issue coming up next, along with shocks and some other work being done on #SR73.

 

Hope this helps.

Thanks

Tim