It’s past time to get it in gear and get the transmission back in shape to get the power from the newly bored out .040 351 Cleveland to the rear wheels.
With the help of my nephew Josh (thanks Josh!!) the transmission was effortlessly (ha) in to place…almost.
Here a more current status video.
All Bolted in.
Now that it’s all bolted in place, I need to work on the getting the kick down road back in place. That’s coming up next on #ProjectSportsRoof.
Welcome back to #ProjectSportsRoof. I run my car projects much like I run my IT projects. You always have to know where to start and know the end game. As with any project that isn’t being built from scratch, in other word, you have to work with what you’ve got, …
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
Well it’s been a long week getting her back on the road. But she drove well enough given her condition.
I am looking for opinions on kits for front suspension rebuilds, mine is shot. At this point I’m probably looking for the cheapest most comprehensive kit given my pony’s condition.
My entire front suspension is not suspending, or bouncing, or quiet. Its time for a full rebuild but I’ve been waiting to blow my motor to justify a full car build! It’s been on its last leg for at least 10 years so at this point I’m trying to see how far I can go to prove Ford’s reliability before tearing her down and she just won’t die! A true survivor.
Also I have a mean top end tick I have lots of play in my lifters, I’m assuming that’s the problem. Already replaced the valve caps, but I probably lost one or two again, any tips or tricks to adjust these ticks?
Although she really like cruising at 50 mph everywhere! I had a hard time keeping it under that speed.
Josh,
You will get a lot of opinions and have a lot of options. Basically is comes down to what you want the car to be. If you just want a cruiser I think you can’t go wrong with just building like it came from the factory. I did that with my 1970 only difference is I use polyurethane bushing. Polyurethane bushing improved the ride without ruining the feel of how the car would have handled when it came from the factory. Properly greased the don’t squeak. If you want it a bit better ride you can upgrade components as you go.
I recommend the RPS kit (it is under $300)
Front Suspension Kit, 1968 – 73 Mustang Restoration Parts Source FDSUSKIT3 – RPS – 004 This suspension kit includes new upper and lower control arms with bushings and riveted ball joints installed, new spring perches and insulators and new strut rod bushings with washers.
Replaces that is, boot as in shifting boot. (Were you thinking…since I just got back from the Barrett Jackson Auction.. I was considering getting rid of the Stang ? Nope..but I tell you there were a couple of cars I’d even swap for…that’s for sure!!) When the 4 speed trans got …
If you searched and found or followed my posts on restoring the dash-board of my ’70 Mustang, then you might recall my planning/scheduling issues. As I was taking the old dash pad off, I realized that I hadn’t order the plastic pillar molding. When I finally called a few Mustang parts …
I’ve the pillar post moldings painted and ready to installed. I put on 3 coats of paint. Now I have to remove the dash pad (again) and install. That will be later this week, my Corvette is still in shop and the Mustang is my back up car. Thanks for reading more to …
Ok now I’m excited. The dash pad replacement arrived and it looks great. Here are some pics: I ordered this part from Dallas Mustang, but I thinking I should have ordered directly from DashesDirect.com I’ll check the web site and see if it was cheaper there. When you have an average guy’s budget …
It always cool to stumble upon a car show regardless of size.
TMC (Tucson Medical Center) opened up a new office just down the road. My wife is a commercial interior designer and does a lot of work through her company for at the TMC facilities.
We were aware of the Grand Opening for this new building but we weren’t there’d be a car show. Here a few of the cars that showed.
You just could walk past this 1959 GMC 100 Pickup. So nicely restored.
Love the steel painted rims!!!
Lots of Chrome on that front end!!
Still being powered by the straight six! The golf club hood prop is a custom touch!
Sparse interior but 100% effective.
Here is a great looking 1962 Ford pickup – still sporting its original V8.
Are you kidding me? Look at this beautiful 66 Malibu!!!
327 Engine (245hp) with Factory Air!!!
Back end jacked up just right!!
There is a lot of tire on that back axle!
That’s all original interior folks!!!
Here are a few more Chevy’s
Beautiful Super Sport w/vinyl top
Wow…is that a BLOWER on top of that power plant?
And another BLOWER!!
56 Chevy Sporting a huge radiator
1980 El Camino – In great shape.
Beautiful Impala…OH…YES..that a Corvette LS3 engine!!!
If you are going to have only one Mopar show up, you want it to be the GTX!! Take a look:
Plymouth Belvedere GTX.
Yes that is a 426 Hemi….going to find two carbs under that air cleaner.
Clean and original interior.
Here a few more of the cars that showed up.
Thanks to my wonderful wife who didn’t mind an interruption in our errands to spend a few minutes at this show.
Coming up more on #ProjectSportsRoof and #ProjectBeepBeep and keep an eye out for our first Facebook Live event.
If you look back at #ProjectSportsRoof post you’ll see the condition engine bay. During those videos I mentioned that I was going to clean it up and hit it with a rattle can. Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
I thought I’d take a minute and catch the readers up on #ProjectSportsRoof. I wanted to touch up some of the engine bay components, horns, vacuum canister and battery tray. I didn’t want to alter some of these too much, I like having the numbers, logos and other info visible, not …
