Category Archives: Muscle Cars

Engine Line Up: 1973 Ford – The 400s Part III

By | | , , , , , , , , ,
Leave a comment

Next up are the Ford 400’s that were available for 1973.

There were 3 options when it can to Ford’s biggest power plants in 1973, the 400 Cleveland the Thunderbird 429 and the Thunderbird 460. If you are thinking…YES!!! More Horse Power!!!! …you are going to be a bit disappointed, compared to today’s standard and the 1960’s standards.

The Cleveland had a cast iron block, over head valves and displaced 400 cubic inches. Its bore and stroke (4.00 x 4.00) and compression ratio (8.0: 1) were choked to death by the two barrel Motocraft carb. It produced only 163 hps

Wimpy - 400 2 barrel intake...needs a 4 barrel intake

Ford ' 73 400 in a wagon

 

 

The two Thunderbird engines (both cast iron with overhead valve) got the privilege of being topped with 4 barrel Motocraft carbs. The 429 displaced 429 cubic inches and the 460 knocked out..yup you guessed it 460 cubic inches.

They had a bore and store of 4.36 x 3.59 and 4.36 x 3.85 respectively and both had the same compression ratio of 8.0:1. The top hp for the 429 was just barely over 200 at 201 and the 460 out did that by 18 giving it a 219 hp.

Fords 460

 

429

 

Here is the twist with these and the rest of the Ford engines.  The horse power stated was changed depending what model the engine was used in.  Most of those in this series were the lowest stated.  For example the 302 was rated at 135 hp in the Maverick, but 138 in the Torino. (Yes, a whopping 3 more hp!!!)

The average difference was between 1 and 5 hps, so we aren’t talking about a bunch of hidden power as they were configured.  But we all know that you pop off  the that 2 barrel carb off any of these engines and plop on wide mouth Holley, and you were going to get much better numbers!!

Thanks for reading.  ’73 Mustang engines coming up.

Tim

Engine Line Up: 1973 Fords Part II – 351s

By | | , , , , , , , , , , ,
2 Comments

Here is the second part of this ’73 line up for the V8.

There were 7 V8 in 1973 (not including the Mustang engines) and the ranged in numbers from 302 to 460 (big number to be sure). Just reading those you think..OH…THE …POWER…NOTHING BUT 100’s RUBBER BURNING, FISH-TAILING HPs!!!…right….uh…NO….these ain’t 60’s engine and they aren’t 2010 engines..nope..they the 70’s engines.  Here’s how they ponied up.

The 302 – Overhead valves, cast iron block with a bore and stroke of 4.00 x 3.00.  Compression ratio of 8.0:1 with 302 cubic inches displaced.  Top that with an awesome 2 barrel Motorcraft carb and you are knocking out 135 hp’s!!!!  Those are number only a grandma could love.  Compare that with the 302 sold under the hoods of Fords in 1970 which yielded 220 hp with a two barrel carb. (Take that 302 bore it .030, toss on a typhoon intake and a 4 barrel Holly you’ll have exactly what currently have in my ’70 Stang.)

My Mustang's Enhanced 302

 

Next up is the family of 351s, the Windsor, the Cleveland and the CJ Windsor.

All three had overhead valves, cast iron blocks and all displaced 351 cubic inches.  They shared the same bore and stroke which was 4.00 x 3.5 and the compression ratios ranged from 8.0:1 to 8.6:1 and the horse power varied by rpm 3800 to 4000 between 156 up to 177, the Cleveland and baby Windsor were choked with a 2 barrel carb while the CJ managed to steal a 4 barrel of the assembly line shelf and had a compression ratio of 9.0:1.   The 351 CJ was able to come in a little more respectable with 266 hp at 5400 rpm.

I will tell you this there were very few 351 CJ Windsor made in 1973 and 1974.  I owned a 1974 351 CJ  and my researched showed that less than 100 of these engined were produced that year.

All of these were used in the Torino, Montego, Mustang, Cougar and other Ford and Mercury models.  The 351 CJ was used in the Mustang and Cougar.

1973 Cleveland 351 2 barrel under the hood of a Mustang.

 

Up next the 400’s for 1973.

Thanks for reading.

Tim

Ford says 200mph was the 2013 Shelby GT500 goal

By | | , , , , , , , ,
3 Comments

Source: MustangsDaily

 

As if the news of the 2013 Ford Mustang Shelby GT500 receiving 650 horsepower and 600 lb.-ft. of torque wasn’t awesome enough, we also found the new Shelby snake was to be capable of 200mph.  When we read the details of this 200mph GT500 feat back in November, we were (for the lack of a better term here) floored.  C’mon, 200mph (stable) from a Mustang?  Crazy enough, it’s just what Ford had in mind the entire time.

Keep reading to get more on this fantastic accomplishment by Ford, Shelby and the SVT engineers & designers.

Back at the 2011 LA Auto Show, Jamal Hameedi (SVT chief nameplate engineer) informed the masses the team had original plans to meet and surpass their original high speed ceiling during testing over in Italy.

“We told the guys to not bother coming back unless they had a two as the first digit…”  –Jamal Hameedi

In order to make the magic happen, the entire SVT team was tapped to make changes to the 2012 Shelby GT500 gearing, body, and suspension to maintain integrity at speed.  What’s most notable is the dual front splitters stacked atop each other, streamlining the draft to make the top speed of 202mph possible.

So…we have the top speed figure for the 2013 GT500; now it’s only a matter of time until we hear/read/feel the official accelerations times & rates.  Keep your eyes peeled for the intel here when it’s known!

WOW!

Thanks for reading

Tim

Engine Line Up: 1973 Fords Part I

By | | , , , , , , , , , ,
2 Comments

1973 was a good year, I was a still in high school and big engines weren’t extinct yet. Ford had a big assortment.  We are talking 10 to choose from if you didn’t count the Mustang engines.

Ford Pinto (this will be a parking log spot light coming up)

On small size 6 cylinder were still king but 4 cylinder was available for the Pinto.  For the larger engines displacement was large and the horse power small.

There was only one 4 cylinder available, reserved for the ill fated Pinto.  It sported an overhead cam and iron block.  It displaced a whopping 122 cubic inches and as one would expect had the smallest bore and stroke – 3.58 x 3.03.  The compression ratio was 8.2:1 and it tore up the street with 86 hps.  (No I didn’t for get the “1” in front of that.)  It was topped with a Ford/Weber 2 barrel carb.

2.0 Pinto Engine

The six cylinders came in 2 varieties  and were used in the Maverick and Torino.  The first was dubbed the Maverick 6 cylinder. It was configured with overhead valves and a cast iron block.  With the bore and stoke 3.68 x 3.13 it was able to displace 200 cubic inches.  The compression ratio was slightly higher than the 4 cylinder at 8.3:1 but it was fitted with a 1 barrel Motocraft carb resulting in only 84 hp.

The second ‘big brother” six cylinder was called the Maverick/Torino.  Again it had the overhead valves and cast iron blocks, same as its little brother, but it had a greater stroke 3.91 (3.68 X 3.91) compared to the its sibling 3.13.  The compression ratio was lower (8.0:1) and topped with the same single barrel carb it managed 88 hps.

The Torino was not a small car so it really need those 4 extra hps!!!

Ford 6 cylinder - nicely restored!!!

V8s  for 1973 coming up and then the Mustang engines.

Thanks for reading.

Tim

The Meaning of Mopar -It Wasn’t Always About Power

By | | , , , , , , , ,
4 Comments

 
For all you MOPAR fans out there this is a great article by Auto Enthusiast.  I’m not going to repeat it all here.  Grab the link at the bottom of this post.

Mopar is a commonly used word in today’s motorsports and high-performance car scenes, but the origins of the term Mopar had absolutely nothing to do with high horsepower or checkered flags.

Chrysler was a young and growing company in the 1920s. It had bought out the Dodge car company in 1928 and the need for a dedicated parts supplier led to the formation of the Chrysler Motor Parts Division.

As the company continued to grow, Motor Parts Division featured a simple logo with the letters C, D, D and P (Chrysler, Dodge, De Soto and Plymouth) from the years 1933 to 1937.

Nelson L. Farley, a sales promotion manager, decided there had to be a better way of promoting the replacement parts. An “Activities Council” was created. Company records show the results of the Activities Council came to light in the spring of 1937. The group came up with “MoPar,” (a simple contraction of the words MOtor and PARts). The first order of business was coming up with a logo to put the name on cans of antifreeze.

The first MoPar logo was oval and used yellow and red. The new logo and the new name were a big move forward in communicating to the customers. If you needed something for a Chrysler product and got it from the garage that sells the vehicles, it came marked as a MoPar item.

The original brand and trademark logo remained the same from 1937 to 1947. It was slightly changed in 1948. The second logo did not change for six years. MoPar parts were still factory replacement items, nothing more and nothing less.

 

 

http://www.amosauto.com/Articles/Mopar/Features/headline-for-web-5

Thanks for Reading.

Tim

Engine Line Up: 1964 Mercury

By | | , , , , ,
Leave a comment

These are some of the best styled cars for that year. ( I really like the convertible for 1963 Merc as well).   The ’64 Comet looked like it was moving, while standing still.

1964 Mercury Comet Cyclone

The engine line up for the 1964 Mercury came in 3 flavors.  The Comet, the Cyclone and Mercury versions.

The Comet engine was a 6 cylinder, overhead valve with a cast iron block.  170 cid with a bore and stroke of 3.50 x 2.93 and combined with a compression ratio of 8.7:1 it produced 101 hps.  Well not actually a powers house with the one barrel carb, C3YF-9510E.

Now the Cyclone engine was a bit of a bump.  It was a V8 with overhead valve and a cast iron block displacing 289 cubic inches. The compression ratio 9.0:1, bore and stroke of 4.00 X 2.37 and hooked up to a 2 barrel carb (C5MF-9510A) helped produce 210 hps.

The 3rd option was the most powerful, producing 250 hps and matched up to the cyclone engine, except where it matters.  Displacing – 390 cubic inches with the bore and stroke 4.05 x 2.37, 9.4:1 compression ratio and topped with  the Ford C4MF-9510D two barrel carb.

Fords 2 Barrel C4MF-9510D Carb

1964 Mercury Colony Park Station Wagon - carried the 390.

 

Thanks for reading.

Tim

Photos: New Ford Mustang 5.0L Falls Three Stories From Parking Garage

By | | , , , , , , , , ,
3 Comments
Posted by

parking garage 2

There has been a lot of parking garage incidents lately but I think this one takes the cake. This isn’t some guy losing control on the nearby road and landing IN the parking garage. Not this time. This time the driver apparently went through the concrete wall of the third story of the parking garage in Lugano, Switzerland, and fell all the way down upon some parked mopeds and a tree. The 24-year old driver was only injured slightly after flying off of the third floor. You can say that this brand new 5.0 suffered a tragic death, though.

If you look up into the parking garage, you see exactly where he fell from as there is a guy looking down and a nice chunk of wall missing. It gives you a good perspective of how far this car actually fell!

1970 Mustang Coupe for Sale – Project car.

By | | , , , , , , , , , ,
10 Comments

1970 Coupe – automatic – desirable 289 engine  – (all there).  $2,600.00

Kim’s husband passed and she’d really like this car go to someone who will restore it and not part it out.  Car will need some work.  If you purchase this car I’ll help project manage the restoration. Might even have some spare part for ya.  Car is here in Tucson.

“1970 mustang coupe for sale. It was my husbands, but he passed away and I don’t have the money to fix it up the way he wanted it to be. I don’t want to sell it for a parts car, I would like to sell it to someone who will restore it and take care of it. It did run at one point, but it has been sitting under a cover for the last 7 years or so so it won’t start. He was in the process of replacing the vinyl roof, so that is why the top is rusty. It probably needs to be replaced. The engine is a 289. All the parts he had bought comes with the car. Extra doors, windows, hood, tail lights…and a few other things. This car is a definite project car!! Any questions, please feel free to email.”

 

There's your 289

Going to need a little work.

Automatic

Thanks”

Here is Kim’s link.

http://apps.facebook.com/marketplace/browse/-/-/usa:az:tucson/?cm_mmc=FB_Friend_Email-_-111206ade03f0aa8c5ed0e10f68f1ddb1ccebf-_-Summary_Local_City-_-100000356349979

Thanks for reading.

 

Tim

Average Guy’s Car Restoration, Mods and Racing – International

By | | , , , , , , , , , , ,
Leave a comment

This blog is gaining popularity.  It’s being followed on Digg, StumbleUpon, Twitter and the Facebook page.

There are car nuts from 18 different countries hanging out around here.  That’s pretty good for an non-commercial blog.

What’s that mean?  Means I’m going to set it up a bit.  More to come on that.

So thank you all and please submit your pictured and stories and I’ll get them posted up.

Thanks for reading.

Tim