Thanks for checking back in on the progress on the 1973 Mustang SportsRoof’s 351C tear down.
In the last post I still needed to remove the lifters and the right side head. To remove the remain head, you have to remove the rockers to get a socket on them.
Also took the time to recheck the push rods, with all the noise coming from the bottom end of the block, you can’t be too careful.
I’ll apologize now for a couple of things. First the fan noise. It’s pretty hot here this time of year in southern Arizona and that fan makes it bearable, barley. But even worse is the compressor noise, so don’t crank up the volume too much. And finally, if you notice, the captions are a bit higher on the video. I’m trying to hide the brand name of my BVDs. Last time readers got a glimpse of the brand, they started sending me their brands to wear on the next video.
As you could see at the end of the video, the cylinder aren’t horrible but not great. But we’ll look at them a bit closer coming up.
Finally the fun part begins. Well actually it’s all fun, just varying degrees of it. Welcome back to the 1973 Mustang project dubbed: #ProjectSportsRoof. We have the 351 Cleveland out and now I’m going to begin disassembly and see if we can get to the bottom of the “bottom end noise” it developed.
Here’s the first video. Don’t be distracted by the Corvette t-shirt from my corvette club, it’s ok to own both!!
Here’s a look at one of nuts from the torque stall converter:
They are pretty rounded.
As you can see I didn’t have you watch as I unbolted the fuel pump or the brackets, even though this is Average Guy’s Car Restoration which equates to average skill set, average tool hoard and average (or below) budget, but I’m thinking you get the removal of a couple of bolts. If things get tricky (for me) I’ll cover it.
Welcome back to #ProjectSportsRoof. With the floor pans welding, sealing and coating finished the next step was to apply the heat and sound barrier. This is …
Time to celebrate!!! The 351 Cleveland is out of #ProjectSportsRoof.
Yeah…I know!! It seemed like to took forever!!! Seems longer since I haven’t driven it in months.
Now if you missed the last post and you are expecting to see a video of the engine coming out, that’s just not going to happen. Here’s a recap of just why there’s no video.
I had made arrangements with my neighbor Dan (Dan did the welding on the floor panels for me) for a Friday he had off to pull the engine. I was going to “work” from home that day and we’d carry out the task in the morning – it’s pretty hot here in Southern Arizona this time of year. Well, I had an issue at work and I had to run in for what I hoped would be only a few minutes – it took until noon.
By then, it was over 100 degrees and when I pulled into my driveway Dan was outside working on one of his projects. After apologizing I changed in to some grubby clothes real quick and we got to work. By then it was about 106 degrees out and of course we are doing this outside. We should have been done by time we actually started and Dan’s adorable twins we hoping to make it the pool before their Dad had to head off to work for the evening.
I mention this all because I’m setting up you for the disappointment, (there is nothing more exciting than getting the engine out – well maybe putting a new one in, it’s a milestone worth capturing on video). Given the above circumstances, I felt it very unfair to ask Dan and the twins to hang out while I stopped to talk you all and then perform a task and then record. So I have no shots or video of pulling the engine out.
351C finally on the stand!
It was an effort but here it is:
And there you have it. #ProjectSportsRoof gave up its 351c power plant and boy does it need an overhaul!!
So keep checking back here (www.agcarrestoration.com) and watch it all unfold!
Thanks for read and drop me a note, love hearing back from readers.
http://wp.me/p2YxYx-4V. Tagged: projectsportsroof … We are moving right along on #ProjectSportsRoof,with the 351 Cleveland rebuilt. Still getting it ready to be …
Jul 31, 2016 … We are moving right along on #ProjectSportsRoof,with the 351 Cleveland rebuilt. Still getting it ready to be pulled from the engine bay In this …
2 days ago … Tagged: projectsportsroof … We are moving right along on #ProjectSportsRoof, with the 351 Cleveland rebuilt. Still getting it ready to be …
This is the last post related to prepping the 351 Cleveland in #ProjectSportRoof for removal.
Originally, I had planned to lift the engine out with the carb still attached. However, after the first test fit to see how the Duralast leveler (I’ve never used one before – last engine I pulled out we used straps on the 318) would be attached, it was clear that the carb had to come off. I thought I’d just be able to attach the Duralast the front part of the engine but unless I added more chain it just wasn’t going to bolt up.
Moving the leveler back a bit to the center if the engine, allowed it to be pull it out with just enough clearance, keeping mind the space limitations between the car bumper and the concrete rise at the garage entrance.
Here’s where you might be a bit disappointed.
I had made arrangements with my neighbor Dan (Dan did the welding on the floor panels for me) for a Friday he had off to pull the engine. I was going to “work” from home that day and we’d carry out the task in the morning – it’s pretty hot here in Southern Arizona this time of year. Well, I had an issue at work and I had to run in for what I hoped would be only a few minutes – it took until noon.
By then, it was over 100 degrees and when I pulled into my driveway Dan was outside working on one of his projects. After apologizing I changed in to some grubby clothes real quick and we got to work. By then it was about 106 degrees out and of course we are doing this outside. We should have been done by time we actually started and Dan’s adorable twins we hoping to make it the pool before their Dad had to head off to work for the evening.
I mention this all because I’m setting up you for the disappointment, (there is nothing more exciting than getting the engine out – well maybe putting a new one in, it’s a milestone worth capturing on video). Given the above circumstances, I felt it very unfair to ask Dan and the twins to hang out while I stopped to talk you all and then perform a task and then record. So I have no shots or video of pulling the engine out.
I can tell you that the torque converter gave us a bit of a problem and here’s one of the reason:
The nuts holding the torque convert on were pretty well-rounded. They been off before.
As soon we had the engine out and got the hoist over the concrete rise between the drive way and the garage floor, I thanked Dan and the twins (they were standing in the garage in full swimming attire – flippers include) for waiting for me. Again a huge thanks to Dan the Neighbor!!!! And yes the twins go to the pool!!!
Now I’ll start the tear down and see what’s going on with the 351C.
http://wp.me/p2YxYx-4V. Tagged: projectsportsroof … We are moving right along on #ProjectSportsRoof,with the 351 Cleveland rebuilt. Still getting it ready to be …
6 days ago … We are moving right along on #ProjectSportsRoof,with the 351 Cleveland rebuilt. Still getting it ready to be pulled from the engine bay In this …
We are so close to pulling out this ’72 351 Cleveland out of #ProjectSportsRoof.
In this post I continue to prep for the removal and I needed to do a trial run fitting the engine load balancing/leveling unit and if I had a enough room to maneuver.
Here’s why:
First there’s a lip I have to take into consideration.
There is a 2″ lip between the garage and the driveway/car.
The distance between the 2″ lip and the car bumper is a concern.
Not much room
Just about 45″
It’s a tight squeeze.
This is the foot of the hoist.
It’s 48″ long.
So I have to fit all of this under the Mustang – BTW there’s jack stands hold up the car and the transmission. When you lower the arm to reach out over the bumper (damn those safety bumpers) the hoist is pressing on the bumper.
Keep in mind that just past the front tires the drive slopes. I had visions of the getting the engine out and having to roll the hoist out past the car and swing it around to lower it on to the engine stand and it getting it away and rolling done the driveway and dumping its self in to the street…I actually had a nightmare about it.
So a dry run was necessary just so I could sleep.
Here’s the video:
I’m going to finish up the prep in the next post.
Thanks reading. We love comments!!! Drop us a note!!!
We are moving right along on #ProjectSportsRoof,with the 351 Cleveland rebuilt. Still getting it ready to be pulled from the engine bay In this posting I’m still …
Welcome back to #ProjectSportsRoof. With the floor pans welding, sealing and coating finished the next step was to apply the heat and sound barrier. This is …
We are moving right along on #ProjectSportsRoof,with the 351 Cleveland rebuilt. Still getting it ready to be pulled from the engine bay
In this posting I’m still fussing around with getting what’s left to be removed and being extraordinarily careful about leaking fluid don’t the driveway.
I have a couple more post dealing with prepping engine to be pulled. So far no real stumbles, nothing has broken and that’s HUUUUGGGGEEEE!!!
Welcome back to #ProjectSportsRoof. I’m prepping the engine for removal in the … Classic Mustangs – #ProjectSportsRoof’s Marti Report · Classic Mustangs …
Welcome back to the final few posts of the floor pan replacement for # ProjectSportsRoof. Let’s get right down to it. I realized that I didn’t catch much of the work …
Welcome back to #ProjectSportsRoof. With the floor pans welding, sealing and coating finished the next step was to apply the heat and sound barrier. This is …
Welcome back to #ProjectSportsRoof. I’m prepping the engine for removal in the next few posts.
The video in this post shows some of the labeling I often do to cover any memory gaps.
The Oil Dri is key to keeping the mess to minimum. That’s important – keeps the HOA out of my hair – bad enough I’m working on the car outside and what you can’t see is that my driveway is steep and any fluid spilled in quantity will run a long ways before it gets to the street!!!
Oil Dri Picked it up at Ace Hardware.
More progress coming up.
Thanks for checking on #ProjectSportsRoof. Hey…if you have a project send us some pic or a video we’ll post them up!!!
Check out our Facebook page https://www.facebook.com/AGCarRestoration/
As I posted before, after a vigorous (not read ‘desperate’) I finally found my next personal project. The 1973 Mustang Sports Roof Fastback is what I settled on. Now we start the project that has been dubbed #ProjectSportsRoof (yes I find it necessary to use the ‘hash’). 1973 Mustang Color …
Well win some and you lose some. If you’ve seen my other posts related the replacement of the points and condenser for the 351C you’ll notice that I gave conversion high marks. This was all based on the years of use I got out of the conversion I did on …
I’ve done all the clean up and all the adjustments necessary to get a good reading on the health of the ’72 351C engine in my 1973 Mustang. The next step is to check the compression. First up was to warm the car a bit and then pull the plugs. Here’s what the …
This is the wrap up on the compression testing for the 1973 Mustang w/ a 1972 351 Cleveland power plant. You’ll might have notices that I referred to the remote tester, which is my code for remote starter…yeah…that’s it!!! All of these tests were dry test and I should have done a …
Thanks for check in on #ProjectSportsRoof. If you remember a of couple months back, shortly after bringing the ’73 Mustang home, I conducted a compression test on all the cylinders. The 351C was running rough (to put it mildly) and smoked like a pile of tires on fire (only the smoke …
Mustang lovers check this out. There is place in El Mirage, AZ called Marti Auto Works. They own the rights to the Ford databases and records prior to 1974 (some models up to 1989). These guys have everything..I mean everything. Give them the VIN number and they’ll pile on the data (it’s not free but very reasonable). They are authorized by Ford to reproduce window stickers and Protector Plates (identification plates that go on the inside door jamb) and more.
If you have a classic Mustang you’ve got to get this report. I thought I’d share mine with the readers. The link below is to the .pdf and here is an image.
Whether you are just interested in the car history or doing an original restore this report comes in very handy. It’s pretty cool to see when it was ordered and build and all the original options are there to match.
The Statistics section – so cool!!! This section lets you know where your car ranks compare to those produce that year. As you can see above #ProjectSportsRoof is o1 of 76 with that paint and trim coat. If nothing else it bragging rights and in some small way this may add to the value of the car, but that’s tough to measure.
The list of items in the Door Data Plate Info, helps you determine how original your might be. For example you can see that my 73 Mustang left the factory with 302 and if you’ve followed my posts on #ProjectSportsRoof you’ll know it now sports a 351C V2 date coded 1972 and a C4 transmission but now it has a date code 1972 C6.
Visit the Marti report site and see what they offer.
