MOPAR’s 318 Part II

Before I start this next segment on the 318, I have to admit that organizing and presenting this work of art (oh..yeah..I’m laughing too!!!!) could have gone in a lot of directions.   The two that stuck out the most for me was by year (chronologically) or by brand.  Neither was a solid idea and at some point in the ’70s the only thing separating brands within most U.S. car manufacturers wasn’t much more than vinyl vs cloth seat covering.  So I decided to go with brands, Chrysler, Dodge and Plymouth, knowing that there we would be some crossover information and it might look a bit disjointed.  There’s some good stuff, and a couple of things you might know about the 318.

Chrysler began using the 318 in 1967 and carried that power plant until the late 1990s.

From 1967 to 1971 the 318 carried a 230 hp rating w/ the standard 2 barrel carb, managed 340 ft lb of torque and sported 9.2:1 compression ratio.  (that is actually a lower compression ratio than the original Ford 250 straight six I took out of my Mustang).  In 1967 the 318 engine was used in the Belvedere, Satellite, Fury, Coronet, Polara and Charger and in 1968 they added as the base option in the Dart GTS and Barracuda.

1967 Polara 4 door.

 

From 1972 to 1979 the 318 was bounced around in the horsepower arena between 150 to 140.  That’s nearly 100 hps lost from the late 1960’s.  At lower end of the new scale were the California models with the extra smog control.   It was still a mainstay, being the base engine choice for the Duster,  Cordoba, Monaco, New Port and unexpectedly the Road Runner,  just to name a few. It was never sported anything bigger than a 2 barrel carb and the compression dropped to 8.5.

It didn’t get any prettier in the 80s either, although there a bit of a bump in the high-end of the hp range to 175 hp but the company more than made up for that dropping the lowest number 120.  Interestingly, they made the California models with 155 hp and a 4 barrel carb.  The compression stayed about the same, but  in ’83 – ’90 they made a HD version of the engine that had between 165 to 175 hp, depending on the year and sported a 4 barrel carb.  This configuration managed to lay down 240 – 250 ft lb of torque, not too bad in one of the lighter cars, like the Dart, but barely power enough for the big old St. Regis. The 318 was also added to some of the most memorable cars….come on..you doesn’t remember “vooo..la rau….oh..oh…” (Volare )and the LeBaron, and Aspen.  Even some larger cars like the St. Regis, New Yorker, Gran Fury (I can’t see any car begin called grand with only 120 hp, but that’s just me.) and the Imperial.

1976 Volare

 

Oh and speaking of the Imperial something interesting happened in 1982 and 1983.  That little something was EFI.  More on that in the next segment.

Thanks for reading.

Tim

’89 318 efi intake to ’79 carbed 318 – Mopar Forums

Hello, my brother and I are thinking of taking on a project and would like to know if the throttle body injection components from the 1989 318 in his truck will work on a 1979 318 engine. The reasoning behind this is due to our …

Auto Factoid 8/8/2010

This isn’t my normal “on this date back in…” factoid.  This one is current.

8/6/2010

At the VW Automóveis Ltda. plant in Portugal today the hundred-thousandth third-generation Scirocco rolled off the production line. Since its launch in 1974, this compact sports coupe has been the most successful Volkswagen two-door with more than 800,000 sold to date. Another notable Giugiaro coupe is the breathtaking beautiful Alfa Romeo Giulia Sprint.

These cars were a hot item in the use for a short while.

2010 Scirocco

 Thanks for reading

Tim

Auto Factoids for the weeks of 7/25/2010 and 8/1/2010

7/26/1945 Kaiser-Frazer Corp organized – it also include what was left of Graham-Paige car manufacturer. Frazer Nash was a British car making company.  In 1953 it became just Kaiser Motors. 

1946 Kaiser Nast Sedan

 

1953 Kaiser Darrin Convertible

 

7/29/1916 Nash Motor Company as founded by Charles Nash when he purchased a company called Jeffery Company which made a car called the Rambler.  I bet you can guess what came eventually  American Motors and their Rambler. 

Oh..in 1909 Buick purchased Cadillac on the 29th day.  

8/3/1900 The Firestone rubber company was founded by Harvey Firestone.  It was based in Akron, Ohio and had only 12 employees. Six years later Mr. Henry Ford contracted with Firestone to supply tires for the Model T. 

8/7/1937 the Cord company stopped production car, but of course when one to build planes etc. 

 Thanks for reading 

Tim

Auto Factoids for the Week of 7/23/2010

7/20/1984 E.L. Cord was in Missouri.  If you think he’s only responsible for the Cord 

1937 Cord

 

 Think again!!!!  How about a company that included Stinson Aircraft, Checker Cab and American Airways (now American Airlines)? But let’s just stay with the cars.  How about the Auburn and Duesenberg?  His history is a good read. 

7/23/1894 first auto race.  It was organized by the Parisian magazine “Le Petit Journal” between the Paris to Rouen.  And the winner was………… Count Jules-Albert de Dion it took  6 hours and 48 minutes at an average speed of 19 km/h (which was approximately 11.806052652509345 p/h). I don’t know what he drove but 2nd places was taken by George Lamaitre and he drove a Peugeot: 

Peugeot 3 hp

7/24/1929 – 2, 000,000 Model A Ford built – A huge milestone. 

1929 Model A

Intro Engine History Segment

If you’ve been reading my “stuff” on this blog or Facebook or Racing in America http://www.racinginamerica.com/ (Henry Ford foundation) you might wonder…what’s wrong with this guy? Does he write for a living?  Well if I did I’d be starving and driving a 1993 Honda Accord with only one plastic hub cap (that’s really my son’s car…he’s a starving artist – I have a plug for him on my blog – RJS Graphic design – he’s pretty good and he won’t strave..Mom won’t have any of that!!) instead of a shiny red 84 Corvette and restored 70 Mustang.  I do it for fun, I haven’t made a single dollar from any of my writing.  I don’t even have sponsors or advertisers for the places I leave my droppings.  Actually this costs me money!!!!

So…yes..I do this for fun and the very informal approach I take…..eeeerrrrkkkkk…..ok folks…I don’t have an approach..real writers do.  The way I like to do this is to just sit down and type…there’s no drafts, unless I save it to finish later, there is no real planning,(hell my poor readers are lucky if I remember to run spell check!!!) other than a Post-It-Note or an email sent to myself when I get an idea.  Nope, I just sit down and type.  If it is on a project I’m working, I sometimes take a break and with the fresh smell of GoJo still on my hands I just start typing and up loading pics.  99.999% of my blogs are done in one sitting.  Type and post. (Sometimes I re-read them…mostly to laugh at my super great witt…HEY!!!!!  DID YOU JUST ROLL YOUR EYES????!!!!  That’s rude!!!)

So I have a list of ideas and one of them was to start a regular piece on engines (I mentioned this a while back.) But man, there’s a lot of stuff out there and great publishing works like the Hemmings nation and Hot Rod magazine do this all time.  Am I going to add some thing never before discussed? Nope.  Am I going to present it in way that nobody ever has?  Well the way I write, yeah probably, no one write like this I don’t think.

My idea was to talk about an engine and include when it was first introduced and what it was used in and for how long, that kind of info.  I’m a big fan of history, history of anything, buildings, streets, towns, cars, really anything that as a little history, I’m interested in hearing about.

So my issue was I just hadn’t sat down and picked one yet to write about.  I was going to do the Ford 302, the engine my Mustang has, or the Crossfire in the Corvette and I will.  But the other day I got my September issue of Classic Car #72 from the Hemmings nation and on the cover was “12 Dynamic Dodge Darts Fun Cars that you must own”.   That triggered a memory of the Dodge Dart I owned when I was in college, I think owned it about 5 months..just long enough to remove all the rust and patch the holes and get it into primer before selling it.

As I read the articles in this issue, I remembered the 318 that my Dart had in and as I read further I decided to kick my series off with Mopar’s 318. 

So over the next few posts I have some interesting details on  configurations and various cars it was used in and some specs.  I’ll try to remember to list the references so you can look up additional info.

Thanks for Reading

Tim

Wrenchin’ Tip 7/18/2010 – Fluid Removal

I recently did some work on my power steering system found this tool to be handy. 

 There is a lot of fluid in the power steering reservoir.  As soon as you release the hoses, it’s going to poor all over the front of your engine and then on the ground.  An oil change tub will help keep it off the garage floor, no staining and no tracking it around. However, it will still run down the  engine.  

So, I used a turkey baster.  EEEERRRKKK…(yeah it’s in caps!!!)  Do not put it back in the kitchen when you’re done….NO…NO..NO….In fact if you are smart, ask first!!!  I did and I was surprised to hear  “Sure, but you’ll have to purchase a replacement.” For a minute I thought….well that’ll come out of my car budget….and I thought…I wonder if I can clean it up…and…ummm…(kidding of course).  It worked great and I just have to purchase one…but not until Thanksgiving!!!!  $10 bucks says..I’ll forget and have to run out on Thanksgiving and stand in line for 1.25 hours, if I can find one at all.  

 BTW – I recommend “Pampered Chef” brand for power steering fluid removal!!!! 

Pampered Chef Turkey Baster

84 Corvette – Power Steering Work II

As I stated in my last post, the molded hose for the power steering unit is no longer made.  So here is an idea that can be used to get around that problem for really just about any regular hose for just about any use. As long as the diameter is correct you can you use metal pipe for the molded portion of the hose.  My plan was to remove the shaped hose and take it to a shop that specialize in shaping pipe or least as a sideline to their metal work business.  They can normally create any shape.  After that is shaped, you can use straight hose on each end to attach to the fittings.  You’ll need two additional hose clamps. This is made easier if you have the metal shop slightly grind down the ends to slide into the rubber hose ends.

 Pls note that you have to be sure that metal is proper for the area you are going to use it in and for the fluid that is going to pass through it.

 So that was my plan for replacing the discontinued hose.  I typed “was” because as I got into the project I realised that particular hose was not necessary to replace.  This was a stroke of luck, because it would have taken a few days with the Corvette apart to get that accomplished.

 I’m going to give you a heads up right now.  I did NOT finish this project just on my own.  Nope, that whole Average skills and Average tools thing plays an important role in accomplishing projects.

 I took a couple of videos and I’ll see if I can get WordPress to work better than last time and I’ll toss them in at the end of this entry.

HELPFUL HINT:  There is a lot of fluid in the power steering reservoir.  As soon as you release the hoses, it’s going to poor all over the front of your engine and then on the ground.  An oil change tub will help keep it off the garage floor, no staining and no tracking it around. However, it will still run down the  engine.  So, I used a turkey baster.  EEEERRRKKK…(yeah it’s in caps!!!)  Do not put it back in the kitchen when you’re….NO…NO..NO….In fact if you are smart, ask first!!!  I did and I was surprised to hear  “Sure, but you’ll have to purchase a replacement.” For a minute I thought….well that’ll come out of my car budget….and I thought…I wonder if I can clean it up…and…ummm…(kidding of course).  It worked great and I just have to purchase one…but not until Thanksgiving!!!!  $10 bucks says..I’ll forget and have to run out on Thanksgiving and stand in line for 1.25 hours, if I can find one at all.  BTW – I recommend “Pampered Chief” brand for power steering fluid removal!!!! The next couple of pics show where we are on the engine and the hoses.

Reservoir and it's bracket

 

Parts Id

 

The two circles indicate the two bolts that need to be, “at the least loosened” if not removed.  You’ll notice that one can not be removed, unless the pulley is removed. I’m not going to take the pulley off and there lies the issue that I needed assistance with. 

But I did manage to remove and check both hoses, which resulted in the determination that the discontinued molded hose was still in great shape and not a threat to leak any time soon. 

Another look at where we are

 

Intro "Kitty" neighborhood cat that often shows up and sits in or on my cars while I work on them. Not having Thumbs, he's really no help.

 

A good look at the hoses. Most of the mess is not from the hose, but the cracked reservoir.

 

Here is at the end of the bulk hose that goes from the reservoir to the power steering pump. 

Old hose 1

 

Old hose 2

 

It was in pretty bad shape. 

PS pump and the mess!!!!

 

And here is the pic with the new hose attached. The hose had to be routed back through the reservoir bracket. 

Hose Upper connection

 

Hose lower connection.

 

As it turned out the actual removal of the reservoir required the removal of some key bolts that did in fact impact the position of the alternator.  As I removed the bolts I noticed the alternator shift.  At the beginning I didn’t think that was possible, because there is a solid bar attached to the alternator and the engine, however it did not.  I had most of the bolt out and decided that I’d better get them back in and I did except one and I should not get that one to line up.  

So off I go to my favorite place down the street and I had them finish it up. 

Here are some after pics. 

Lower Hose connection and PS Pump

New reservoir.

Another repair down.  It’s been a couple of tough months for the Corvette and her engine is going to need a good detailing, but not just yet.  I have another huge modification come up…a new intake.  That will be pretty soon, so keep checking back. 

Thanks for reading. 

Tim. 

84 Corvette – Power Steering Work

Two guesses as to my next project on my C4……cricket…cricket…cricket…Give up?   Fine, its replacing the power steering reservoir and connected hoses.

Just for fun?  Nope, who’d want that mess of a job, just for fun?  No…no it is not an upgrade but a serious leak. 

Hey kids its story time!!!!  Let me tell you about the big shiny Vette that ate all of the average guy’s car budget.  Grab you binkies…it’s horrifing.  

If you’ve been reading my posts, you may recall (“come..you ‘member!!!” {I stole that from the comedian George something}…..What you don’t hang on every word I type?…You don’t re-read my post to memorize all my car woes and tips and humor???..that’s what I figure…yet I keep on typing….its good therapy for me!!!) that my vette over heated, not once, but twice!!!   Freak catastrophic radiator hose split and then the fan frying it’s self.   

After I got it back from the shop, where I had them check the electric work I did when installing the new fan, I noticed a leak under the car in the driveway.  I hate leaks under my cars, almost as much as the Ms. hates the side affects they have on our driveway (I’m not crazy about them either).  The leak was not too big and when I cleaned it up, I chalked it up to left over coolant from the over heading, it had the right consistency. Then I washed the car.  Nice shiny beautiful red…money swilling Corvette!!!! 

Drove the car to work and home again and came back out a bit later to put the garbage cans on the curb….errrkkk…hey…Tim..no one, not one single person, cares why you came back outside, and just as many care where you put the trash cans… and I’m going out on a limb here…but I’m betting the total is the same for whether you drove it to work…to the store…or Japan…got it bro???!!!  These are valuable minutes of our lives being spent here reading this!!   Ok..I got it. The pool was bigger than before and it no longer could be mistaken for coolant.  It was without a doubt, transmission fluid, or power steering fluid.  Whether it is GM or Ford, either of their recommend power steering fluid looks and feels similar to the transmission fluid. 

Dreading the worse news, I decided to first check what I hoped was the problem, power steering fluid, I’d hate that less then tranmission issues.  Luckily…(isn’t that the way it is with older cars..your happiness is measured by the size of what’s broken, or needs replacing)…it appeared that it was just the top of the hoses on the reservoir, near the hose clamps…perfectly understandable….it’s an old car..and simple to replace (remember that later on in this post). 

Here are the hoses: 

Hoses leaking near the clamps.

 

I’m thinking…oh..”SLAM DUNK” easy fix.  Perhaps, but come on….really….does it really ever turnout that easy…yes it does…but not this time!!! 

After further inspection, I noticed something else..oh…you’ll love it!!  I’d tell you but you know a pic is worth 250 cuss words (most of those aren’t real words but I do have some unique arrangements of the classic 4 letter ones and a few bigger).  Ready???  NO!! For the pic… make up your own cuss phrases!!! 

Sigh!!!

 

Well that does make it a clean sweep…everything above the pump up needs to be replaced!!!  Ok, still not horrible, so I’m much happier knowing it’s not the transmission!!!!  Just order the parts and we are home free. 

And that’s the end of the story…expect for the part where the hoses aren’t available any more and OMG, you betcha, they aren’t straight hoses.  Here…take a look!!! 

From the reservoir, down to the pulleys, nothing but bends!!!

 

Better look at the hose going straight down the Front of the engine block

 

They are molded to hold shape, there is no room for anything but the exact bends or they will rub against the pulleys and last..oh..maybe a week!!  

And finally… 

And a little wider view.

 

The reservoir and one hose that is supposed to fit are on their way…be here tomorrow. The other hose is not available…no not out of stock and on back order…not made any longer.  

But I have an idea….I’ll give that to you tomorrow. 

Thanks for reading 

Tim

Auto Factoids for the week of 7/11/2010

We got a first and a last on the same day – 60 years apart.

7/12/1922 – Frist Checker automobile  built

1922 Checker Cab

 

7/12/1982 – Last Checker automobile built

1982 Checker Cab

 

7/14/1955 – First Karman Ghia – I really like these cars.  I might own one some day, but maybe a Covair instead!!!

1955 Karmann Ghia - didn't change much from '55 - '74

7/16/1935…first parking meter in place in Oklahoma City, 30 minute later was the first parking ticket.

First Parking Meter

Thanks for reading

Tim

Auto Factoids for the Week of 7/4/2010

Here ya go, enjoy. 

7/6/1946…..U.S. began producing car again after World War II.  It is a bit misleading but some cars companies did continue to produce cars.  At the very onset of the war (1942 thereabout), some of the first effort were to build the cars without all the chrome, painting the trim instead, the first “blacked out” (they were actually called “blackout specials or models” ) which became popular with the grilles in muscle cars later on.  Washington dictated that stainless-steel and chrome would not be allowed on cars except on of bumpers, bumper guards, and windshield wipers. 

1942 Chevy Front.

 

1942 Chevy Backside

 

I think it looks great!!! 

7/8/1909  The first Hudson was built. 

Hudson Roadster from 1909

 

Thanks for reading 

Tim