ProjectBeepBeep – 68 Road Runner Valve Cover Gaskets Part II

Bill gives some tips on cleaning up the valve covers and tries valve cover studs.


Wrap up of the valve cover gasket replacement is up next.

Thank for reading.

Tim

#ProjectBeepBeep

 

 

68 Road Runner Gets it’s Beep Beep back!!

While trying to warn a real life coyote of his ‘rapid’ approach, Bill’s 1968 Road Runner (#ProjectBeepBeep) failed to issue the famous BeepBeep, or was that just part the car’s instinctive DNA based response to coyotes in general? Either way Bill tackles the problem. Here’s a shot of the horn. More coming up …

Project BeepBeep – 68 RoadRunner – Body Bumpers Kit

Bill takes a look at MOPAR Body Bumper Kit for #ProjectBeepBeep and shows a common mistake made when a car is painted. Bill is correct that the bumper are painted over show an oversight that might just tank the value of your car. I grew up working in my Dad’s body …

 

ProjectBeepBeep – 68 Road Runner Valve Cover Gaskets Part 1

Continue following Bill’s journey to a “Leak Free MOPAR” for his 1968 Road Runner. #ProjectBeepBeep

Wild E. Coyote is back!!!  Apparently he’s been working at Summit Racing!!!!

BeepBeep is getting some new valve cover gaskets!!!!  But will that stop the leaking?!?!?!?!

 




 

More coming up.

Thanks for reading/viewing.

 

Tim

68 Road Runner Gets it’s Beep Beep back!!

While trying to warn a real life coyote of his ‘rapid’ approach, Bill’s 1968 Road Runner (#ProjectBeepBeep) failed to  issue the famous BeepBeep, or was that just part the car’s instinctive DNA based response to coyotes in general? Either way Bill tackles the problem. Here’s a shot of the horn.   More coming up …

Project BeepBeep – ’68 RoadRunner – Door Panel Tips

Ready for some more #ProjectBeepBeep?  Bill takes you through a few tips for restoring your B-Body door panels. Take a look:     Great stuff!!!  Thanks Bill!!! Have a few Mopar tips – Post them up or drop me a note @ agcarestoration@cox.net and we get you video/tip posted on the site. Thanks for reading Tim                 Introducing …

Project BeepBeep – 68 RoadRunner – Body Bumpers Kit

Bill takes a look at MOPAR Body Bumper Kit for #ProjectBeepBeep and shows a common mistake made when a car is painted.   Bill is correct that the bumper are painted over show an oversight that might just tank the value of your car. I grew up working in my Dad’s body …

Project BeepBeep – 68 RoadRunner – Disc Brake Conversion Part 5 and Some Dash Work

Welcome back to #ProjectBeepBeep. Bill is working on finishing up the brake conversion. Here is a progress update. Note:  I forgot to add the credits for these videos:   Starring Bill B as himself; BeepBeep as ’68 Road Runner; Wild E. Coyote in effigy Camera Production; Mrs. Bill B and SamB Editing Tim …

Project BeepBeep – 68 RoadRunner Dash Update

Welcome back to #ProjectBeepBeep.  Thanks for checking in on the progress of Bill’s 1968 Plymouth Road Runner. If you recall mixed in with some brake updates,  Bill mentioned that he had sent out the circuit board for a restored.  Here is an update on the status of the dash.     Next up an …

 

 

Project BeepBeep – Oil Pan Gasket Part III

Wrapping up the oil pan gasket and what’s next for the 68 RoadRunner?

Take a look:


I have to add my note and this might rub someone the wrong way but I am going to toss it out here.

I took my 1970 Mustang to a shop run by a guy I trust with my cars.  After getting the Mustang back I leaked from two spots.  When I asked his mechanic about the said  “Old cars leak.”   That phrase really irritates me every time I hear it.   This day in age with all the improvement in gaskets from rubber to rubber coated metal to make your or form you own, this just no reason for your car to leak.  After the incident above, I took my Mustang home and replaced the gaskets and drove it for about a week and then went back to my friends shop and had the mechanic look under the car…it was bone dry.

Unless you have a part that can’t be found there is almost no reason, given all the options, for your old car to leak.   Having said that, Bill makes a good point – there are times when a leak, a non-engine killing leak, becomes to expensive or time consuming to fix.   But if I know Bill, you’ll be seeing a video with him fixing all the leaks.    (;^o)

Thanks for reading.

Tim

 

 

73 Mustang (Project SportsRoof) Engine Dress Up and Venting/Vacuum

Did you think I sold #ProjectSportsRoof?  Nope.  I’ve been busy and I’ve been serving as editor to another cool project – my constant reader Bill’s ’68 Plymouth RoadRunner (#ProjectBeepBeep). However, I have been doing some work on the sports roof and in this video you’ll see a little bling under the …
Introducing #ProjectBeepBeep – Code H 1968 Road Runner

I’d like you to take a look at one of my constant readers classic muscle car. First let me say that Bill has been an a long quest to find a car to replace this car:   Back in the day. It was a long search with lots of phone calls with many …

 

Project BeepBeep – Oil Pan Gasket Part I

Welcome back to AGCR.  While I’m hoping that #ProjectSporsRoof get make to my driveway this week, Bill it taking on the old adage “Old Car Leak”.

First up for #ProjectBeepBeep (Bill’s beautiful 68 Road Runner) oil pan gasket.

 

 

Here are the box-end wrenches, I mentioned in the caption.

 

More on #ProjectBeepBeep coming up.

Thanks for reading.

Tim

 

ProjectBeepBeep

68 Road Runner Gets it’s Beep Beep back!!

While trying to warn a real life coyote of his ‘rapid’ approach, Bill’s 1968 Road Runner (#ProjectBeepBeep) failed to  issue the famous BeepBeep, or was that just part the car’s instinctive DNA based response to coyotes in general? Either way Bill tackles the problem. Here’s a shot of the horn.   More coming up …
Introducing #ProjectBeepBeep – Code H 1968 Road Runner

I’d like you to take a look at one of my constant readers classic muscle car. First let me say that Bill has been an a long quest to find a car to replace this car:   Back in the day. It was a long search with lots of phone calls with many …

Project BeepBeep Get’s Even Cooler – Part Two

Welcome back!!!

After finding a leak in the radiator, Bill decided to replace the it with an after market unit.

Here is Part Two of the process.

 


More coming up with Bill’s warp up of the radiator swap for his 1968 Road Runner!!!

 

Thank for reading.

Tim

#ProjectBeepBeep

#ProjectSportsRoof

 

68 Road Runner Gets it’s Beep Beep back!!

While trying to warn a real life coyote of his ‘rapid’ approach, Bill’s 1968 Road Runner (#ProjectBeepBeep) failed to  issue the famous BeepBeep, or was that just part the car’s instinctive DNA based response to coyotes in general? Either way Bill tackles the problem. Here’s a shot of the horn.   More coming up …
Project BeepBeep – ’68 Road Runner -Disc Break Conversion Part 2

Thanks for checking back in on #ProjectBeepBeep. Having made the decision to convert the front brakes from shoe to disc Bill gets started with this major project for #ProjectBeepBeep. He went with a kit from Dr. Diff and here’s a brief look at some of the contents.   Nice shiny new rotors!! Spindle …
Project BeepBeep – 68 RoadRunner – Body Bumpers Kit

Bill takes a look at MOPAR Body Bumper Kit for #ProjectBeepBeep and shows a common mistake made when a car is painted.   Bill is correct that the bumper are painted over show an oversight that might just tank the value of your car. I grew up working in my Dad’s body …
Project BeepBeep – 68 RoadRunner – Disc Brake Conversion Part 5 and Some Dash Work

Welcome back to #ProjectBeepBeep. Bill is working on finishing up the brake conversion. Here is a progress update. Note:  I forgot to add the credits for these videos:   Starring Bill B as himself; BeepBeep as ’68 Road Runner; Wild E. Coyote in effigy Camera Production; Mrs. Bill B and SamB Editing Tim …
Project BeepBeep – 68 RoadRunner Disc Brake Conversion – FINAL CHAPTER!

Welcome back to the #ProjectBeepBeep.  We are still following Bill’s progress on the front disc brake conversion for his 68 Plymouth Road Runner. Did I say this is the final chapter?   Well….     Sometimes during a project you just can’t afford the time to do a video, especially when you have a friend …

Project BeepBeep Get’s Even Cooler – Part One

Welcome back to Average Guys Restoration.   It’s been a while since I’ve been able to get you some updates on Bill’s beautiful 1968 Road Runner and Bill’s as tackled a few projects.

Just recently he found a leak in the radiator and he documented the mini project.  Here is part one:

 


I have more coming up on the 68 Mopar and #ProjectSportsRoof!!!

Thanks for reading.
Tim
 

68 Road Runner Gets it’s Beep Beep back!!

While trying to warn a real life coyote of his ‘rapid’ approach, Bill’s 1968 Road Runner (#ProjectBeepBeep) failed to  issue the famous BeepBeep, or was that just part the car’s instinctive DNA based response to coyotes in general? Either way Bill tackles the problem. Here’s a shot of the horn.   More coming up …
Introducing #ProjectBeepBeep – Code H 1968 Road Runner

I’d like you to take a look at one of my constant readers classic muscle car. First let me say that Bill has been an a long quest to find a car to replace this car:   Back in the day. It was a long search with lots of phone calls with many …
Project BeepBeep – ’68 Road Runner – Drum or Disc – The Decision

1968 Ply Road RunnerProject BeepBeep Welcome back to #ProjectBeepBeep.  Bill is looking at the brakes and gets some professional assistance to help him make a crucial decision.  You know if you’ve got a lot of GO…you need a lot STOP. It not an easy decision to alter a car’s originality, especially …
Project BeepBeep – ’68 Road Runner -Disc Break Conversion Part 2

Thanks for checking back in on #ProjectBeepBeep. Having made the decision to convert the front brakes from shoe to disc Bill gets started with this major project for #ProjectBeepBeep. He went with a kit from Dr. Diff and here’s a brief look at some of the contents.   Nice shiny new rotors!! Spindle …
Project BeepBeep – ’68 RoadRunner – Door Panel Tips

Ready for some more #ProjectBeepBeep?  Bill takes you through a few tips for restoring your B-Body door panels. Take a look:     Great stuff!!!  Thanks Bill!!! Have a few Mopar tips – Post them up or drop me a note @ agcarestoration@cox.net and we get you video/tip posted on the site. Thanks for reading Tim                 Introducing …

 

Project SportsRoof Update

Well it has been a while since I’ve updated readers on #ProjectSportsRoof and frankly there hasn’t been a lot going on.

As the regular readers know I do all the work I can on my car, when practical.  This work happens in my driveway, which unfortunately has a rather steep slope.

You’ve seen the videos of my work pulling out the engine and the transmission and putting the engine back in and attempting to put the transmission back in.

I few weeks ago, after suffering from a huge bout of guilt for not working the Mustang, I attempted one more time to get the transmission reattached to the engine.

This endeavor, required me to put the car up a lot higher than normal on the stands, to get enough room to maneuver the trans and the transmission jack around.  this was a huge mistake.  After a few tries I decided to pull the transmission back out for under the car and wait for some help later in the week.

Everything went fine and the transmission was safely strapped to the transmission jack and rolled back into the garage.  Since the car was lifted higher for the failed attempt, I decided to lower it back on to the ground.  As I lifted the car with my floor jack, so I could remove one stand one of the remaining stands slipped from its place and the car dropped about 5″ on to the tires.  This didn’t seem to be to dramatic of a fall until I noticed that the motor mounts had separate (broke to be frank).

That was depressing, to say the least and another set back.  Of course this depression was compounded by the fact that  I had very limited free time coming up to work on the car.  I am a full-time Junior High teacher and I had just signed on to coach our boy’s basketball team which was a lot of fun (we when 10 -2 for the season) and very time-consuming.

I purchased the motor mounts and was attempting to schedule a couple of relatives to help out.  That proved difficult.

So a relative mentioned a successful automotive shop that was opening a new location here in Tucson and I contacted them to see they wanted to tackle the engine and transmission re-install, build a custom drive shaft and add headers and exhaust.  They looked it over and we agreed on the cost estimate.

So off she goes to get the complete drive training straighten out and hopefully back on the road soon.

There is still a lot of work to be done and as I get ready for my summer break from teaching, I should be able to but more time into it!!!

 

I have a lot more coming up on #ProjectBeepBeep as well.

Thanks for reading.

1973 Mustang Project SportsRoof – Exterior Walk-Around

Welcome back to #ProjectSportsRoof.  I run my car projects much like I run my IT projects.  You always have to know where to start and know the end game.   As with any project that isn’t being built from scratch, in other word, you have to work with what you’ve got, …
1973 Mustang – Engine Bay Work

If you look back at #ProjectSportsRoof post you’ll see the condition engine bay.  During those videos I mentioned that I was going to clean it up and hit it with a rattle can.  Again this isn’t going to be a concours restoration, it’s going to look nice and it’s going …
1973 Mustang – Project Sports Roof

As I posted before, after a vigorous (not read ‘desperate’) I finally found my next personal project.  The 1973 Mustang Sports Roof  Fastback is what I settled on.  Now we start the project that has been dubbed #ProjectSportsRoof (yes I find it necessary to use the ‘hash’). 1973 Mustang Color …
1973 Mustang – Project Sports Roof – Fender Fitment Part I

Ok so these were suppose to kick off while I’m over here in Italy, but they failed to post up, so I’m taking a few minutes to fix that. Oh well as long as I’m typing, here is my favorite Italian road sign: Welcome back to Project Sports Roof (#ProjectSportsRoof).  We stripped …
1973 Mustang – Project Sports Roof – Fender Fitment Part II

In these next two videos, you’ll see just how ‘off’ these fenders are in some areas and surprisingly how well they fit in other areas. If you have an experience or a hit for anyone taking on this part of a restoration – drop a comment here and we’ll share them. https://youtu.be/Ga9EHbDpSfg     https://youtu.be/FBKs7EG4kK0   Thanks …
1973 Mustang – Project Sports Roof – Pertronix Ignitor Update

Well win some and you lose some.  If you’ve seen my other posts related the replacement of the points and condenser for the 351C you’ll notice that I gave conversion high marks.  This was all based on the years of use I got out of the conversion I did on …
1973 Mustang – Project Sports Roof – Vacuum System Part II

Thanks for checking on #ProjectSportsRoof.   So here is the last set of initial questions. Here is an image of the current set up: Any diagram I find has the hose vacuum from the Distr going to the Valve assy. The Valve assy has nothing attached which is located on the front …

Tim

#ProjectSportsRoof

#ProjectBeepBeep

68 Road Runner Gets it’s Beep Beep back!!

While trying to warn a real life coyote of his ‘rapid’ approach, Bill’s 1968 Road Runner (#ProjectBeepBeep) failed to  issue the famous BeepBeep, or was that just part the car’s instinctive DNA based response to coyotes in general?

Either way Bill tackles the problem.


Here’s a shot of the horn.

 

More coming up on #ProjectBeepBeep and #ProjectSportsRoof.

Thanks for following our projects and find us on FaceBook @ www.facebook.com/AGCarRestoration/

Tim

Introducing #ProjectBeepBeep – Code H 1968 Road Runner

I’d like you to take a look at one of my constant readers classic muscle car. First let me say that Bill has been an a long quest to find a car to replace this car:   Back in the day. It was a long search with lots of phone calls with many …

Project BeepBeep – ’68 Road Runner – Drum or Disc – The Decision

1968 Ply Road RunnerProject BeepBeep Welcome back to #ProjectBeepBeep.  Bill is looking at the brakes and gets some professional assistance to help him make a crucial decision.  You know if you’ve got a lot of GO…you need a lot STOP. It not an easy decision to alter a car’s originality, especially …

Project BeepBeep – ’68 Road Runner -Disc Break Conversion Part 2

Thanks for checking back in on #ProjectBeepBeep. Having made the decision to convert the front brakes from shoe to disc Bill gets started with this major project for #ProjectBeepBeep. He went with a kit from Dr. Diff and here’s a brief look at some of the contents.   Nice shiny new rotors!! Spindle …

Project BeepBeep 68 Road Runner – Fender Brace Repair

Welcome back to #ProjectBeepBeep, Bill’s 1968 Road Runner.  Bill has been moving long with small projects on BeepBeep and I’m try to play catch up with will all my blogging.

While going over his car with magnifying glass Bill found a crack in one of the inner fender well brace.  Over time this can cause issues.  Here’s how the fix went.



Ok, so often when you are working on a project it, recording it has to take a back seat so it doesn’t slow progress and in this case doesn’t take up extra time when a friend is lending a hand.

After the welding there was a little bit of heat damage that needed to be tended too.  Check out the wrap up of this project:

 


 

Thanks for following along.  There will be more coming up.

 

Tim

 

 

Kart Graveyard – Death of an Industry

While wandering around a small town in Southern Arizona my wife and I came across this kart display which I dubbed “Kart Graveyard”

Some of these cars in the pictures above had complete brake systems and somewhat refined steering.

Finding this graveyard got me thinking about the manufacturers of these cool play things and I ran across this website and shared it here.

http://www.e-kmi.com/ArchivesPost2005/ft/THE SLOW DEATH OF AN INDUSTRY Opinion by Darrell Sitarz.htm

THE SLOW DEATH OF AN INDUSTRY Opinion by Darrell Sitarz

In the 1990s, the American fun kart industry was churning out nearly 200,000 units annually by nearly 3 dozen manufacturers. Today, there are only a handful of fun kart makers still remaining.

So, what has caused the downfall of what was one of the largest portions of the go-kart industry? Some cite the high cost of liability insurance, some say it’s the imported karts or the ATVs while others think it’s because of cost of mandated safety features which added to the overall cost. It may be one or two, or it may be all of the above; so let’s look at it item by item.

COSTS
In the mid-1990s, the US Consumer Products Safety Commission targeted the fun kart industry and asked it to look into setting manufacturing guidelines and to increase and standardize safety features. With those as goals, the American Fun Kart Association (AFKA) was formed by the manufacturers and suppliers and standards were subsequently set. The AFKA was commended by the CPSC on their ability to take on the problem and do what was necessary to help insure public safety. The solution to the safety problem however led to another, that of increasing the cost of manufacturing a kart, the cost of which was, of course, passed onto the consumer. At that time, a few manufacturers decided to cease production feeling they could not compete in the marketplace due to the increased manufacturing costs.

IMPORTED KARTS
With costs rising, some manufacturers went overseas with an eye to reduce costs by importing karts.

“The problem was that the overseas manufacturer would make three vehicles. One was for their customer in the states and two for them to bring over here and sell under a different brand name,” an industry source said. “This would give them a foot hold in the US with a proven design that had historically sold. They could sell it cheaper because it came with their own engine that looks very much like a proven US motor and they don’t pay product liability insurance.”

So in essence, the manufacturers that went overseas were now competing with themselves. The results: more manufacturers went down the tubes.

ATVs
And here’s a strange twist of fate. Back in the late 1980s three-wheel ATVs were banned because of safety concerns in the US. Suddenly wham!, the fun kart industry began it’s upsurge in sales again topping out at nearly 200,000 units annually. So now what’s happened? The resurgence of the “new” ATV, a four wheeled version with more features and major off-road capabilities has also had a hand in the downfall of the fun kart industry. In 2004 for example, 817,000 ATVs were sold which is 4 times the amount of go karts in the industry’s best year.

PRODUCT LIABILITY INSURANCE
The slow death in the industry was caused by several factors, the main one may have been the tremendous cost of product liability insurance. It got to the point that most of the kart makers could not afford it.

“The manufacturers were not supported by the insurance companies that would accept premiums and not fight the cases but would make settlements and in turn would raise the rates for all kart manufacturers,” a reliable industry source told e-KMI. “Lawyers would represent the karts owners because they knew there would be a settlement and they would get paid. Getting hurt today is like winning the lotto but even better because it is tax free! People don’t have to accept responsibility for their actions because there are lawyers that will represent you know matter how stupid your action was because “we will get you something”.”

One or a combination of all of the above have taken their toll with the fun kart industry. But whatever the case may be, the industry appears to be in serious difficulty and is looking for answers, if there are any?

The following is a partial list of US fun kart manufacturers which have gone out of business or have ceased fun kart production since 1990.

Action Fun Karts
Avenger
Bird
BKS
Brister’s Design and Manufacturing*
Brister’s Thunder Karts
Clark Karts
Chief Karts
FKL
Fun Karts LA
Hamilton Brothers
Hang 10
Hoffco
Karts International
K-C Manufacturing C., Inc.
Klipper (not producing fun karts but still making promotional go-karts)
Midwestern Industries (acquired by T & D and now producing promo karts)
Minati (Brave Industries)
Murray*
Moto Machine
Performance Industries
Polaris (never made karts but had Brister make karts to test the market)
Robron
Simplex
Scat Fun
Tiger Industries
Trampolking
USA Industries
Yerf-Dog*

* Ceased fun kart production in 2005

Current US Fun Kart Manufacturers:

Carter Brothers
KartCo
Ken-Bar
Manco

 

Thanks for reading.

Tim

antique kartsantique karts