Category Archives: Car Models

Engine Line Up: 1973 Fords Part I

By | | , , , , , , , , , ,
2 Comments

1973 was a good year, I was a still in high school and big engines weren’t extinct yet. Ford had a big assortment.  We are talking 10 to choose from if you didn’t count the Mustang engines.

Ford Pinto (this will be a parking log spot light coming up)

On small size 6 cylinder were still king but 4 cylinder was available for the Pinto.  For the larger engines displacement was large and the horse power small.

There was only one 4 cylinder available, reserved for the ill fated Pinto.  It sported an overhead cam and iron block.  It displaced a whopping 122 cubic inches and as one would expect had the smallest bore and stroke – 3.58 x 3.03.  The compression ratio was 8.2:1 and it tore up the street with 86 hps.  (No I didn’t for get the “1” in front of that.)  It was topped with a Ford/Weber 2 barrel carb.

2.0 Pinto Engine

The six cylinders came in 2 varieties  and were used in the Maverick and Torino.  The first was dubbed the Maverick 6 cylinder. It was configured with overhead valves and a cast iron block.  With the bore and stoke 3.68 x 3.13 it was able to displace 200 cubic inches.  The compression ratio was slightly higher than the 4 cylinder at 8.3:1 but it was fitted with a 1 barrel Motocraft carb resulting in only 84 hp.

The second ‘big brother” six cylinder was called the Maverick/Torino.  Again it had the overhead valves and cast iron blocks, same as its little brother, but it had a greater stroke 3.91 (3.68 X 3.91) compared to the its sibling 3.13.  The compression ratio was lower (8.0:1) and topped with the same single barrel carb it managed 88 hps.

The Torino was not a small car so it really need those 4 extra hps!!!

Ford 6 cylinder - nicely restored!!!

V8s  for 1973 coming up and then the Mustang engines.

Thanks for reading.

Tim

Photos: New Ford Mustang 5.0L Falls Three Stories From Parking Garage

By | | , , , , , , , , ,
3 Comments
Posted by

parking garage 2

There has been a lot of parking garage incidents lately but I think this one takes the cake. This isn’t some guy losing control on the nearby road and landing IN the parking garage. Not this time. This time the driver apparently went through the concrete wall of the third story of the parking garage in Lugano, Switzerland, and fell all the way down upon some parked mopeds and a tree. The 24-year old driver was only injured slightly after flying off of the third floor. You can say that this brand new 5.0 suffered a tragic death, though.

If you look up into the parking garage, you see exactly where he fell from as there is a guy looking down and a nice chunk of wall missing. It gives you a good perspective of how far this car actually fell!

Mustang Project Guy’s Slice of Heaven

By | | , , , , , , , ,
12 Comments

“Honey…I found our next vacation spot..hear they got a  nice Motel 6 nearby!!!”  “Honey…can we  go now?!!! The Turkey will keep until next week!!!”

Photos: World’s Largest Ford Mustang Salvage Yard

Posted by on November 21, 2011 – 2 Comments

salvage 8

Everybody knows that saying “I’ve died and gone to heaven”, and this applies to most enthusiasts in this junkyard full of old decrepit Ford Mustangs. Especially, the project guy that has an old classic sitting in the garage. I’m sure it could go either way, though, as some might consider this a sore sight with so many wrecked and rusted ponies. This is the Colorado Mustang Salvage Yard.

Soooo, anybody down for some campin’?!

Colorado Mustang Specialists, Inc. began in a two-car garage in 1972. Mustangs were as numerous as hippies on a Boulder park lawn, easy to buy, fix and sell. So, a would be University of Colorado student found a lucrative way to pay his rent and tuition. After graduation the diploma went in a drawer and the horsing around got serious. Wrecked, junked and abandoned Mustangs were cheap and plentiful, so the collection started that eventually led to the worlds largest Mustang salvage yard.

Most recent and exciting to us is the addition of modern fuel injection conversions, for 64-1/2 to 85 models. These conversions and related parts let the novice enthusiast bring his early Mustang into the new millennium with a computer driven, fuel-injected, V-8 power train, meeting todays standards without changing the Mustangs classic design. We predict these conversions will open a fun and exciting new era of Mustang enthusiasm.

Parking-Lot Spotlight 1955 Chevy Belair

By | | , , , , , , , , ,
10 Comments

Note: Updated to correct mis-Identification of this parking-lot find.  It is in fact a 1955.  The main details that denote the difference is the placement of the Chevy and BelAir badging and grile.

So I’m lucky. I live in a place where there is not prone to any type of natural disasters, we don’t much rain and it only snow when it’s a cold day, you know where.

It’s also a place were you don’t have to put way your collectible set of wheels, you can drive the year would and a lot of folks do.

Here is my latest parking-lot find.

It is a 1955 Chevy, 2 door Belair.  Yeah, I know it’s a couple years before the super wonderful 1957’s came out, but I like these shoe box cars, with their very clean lines especially the 2 door version and I particularly like the lines of the BelAir convertible.  It reminds me of the clean lines for my 1966 Chevy Impala convertible.

Love the red and white.  Fantastic chrome.

Wheel aren’t ordinal but I think that are great for this car.

Look at the stance! It’s just great.

You gotta love that hood ornament!!

 

All Belair came standard with a 6 cylinder with about 353,00 produced, not counting convertibles.

The 6 was an overhead value, cast iron power plant with a displacement of 235.5.  With a 3 9/16 x 3 15/16 and a compression ratio of 7.5:1
these cars knocked out a whopping 115 hp.  The would breath through a Rochester one barrel Model 7007200 carb or a Carter one-barrel Model
2101S (for the Powerglide auto transmission) and a Rochester one-barrel Model 7007181 for the standard shift.

Thanks for reading.

Tim

Car Production Numbers. They Made How Many? 1922

By | | , , , , , , , , , , , , , , ,
Leave a comment

It is 1922 and the car industry is moving right along.  Small start-up car companies pop up here and there in the 1920’s.

Here is how they stacked up for 1922.

Top spot was Ford  producing 1,147,028 cars.

Dodge was a very distant second with 152,653 car rolling off their assembly line.

Chevrolet ran in third place with 138,932 cars made.

And finish up the list were Buick with 123,152; Studebaker with 105,005; Williys-Overland with 95,410; Durant with 55,300 and finally Maxwell/Chalmers 44,811.

Total passenger cars produced were 2,274,185 with 269,991 truck being made.

Rickenbacker was a new upstart beginning production in 1922.

Durant produce a car priced at $319 . Ford reduced prices to $298.

Balloon tires were introduced.

Hey fuel gauges began being installed in dash in 1922.

1922 Durant Star - An attempt to undercut Ford's prices

1922 Rickenbacker 4 Door

I love this one:

1922 Chrysler Panel Truck

Thanks for reading.

Tim

What’s coming up? Take a look!

By | | , , , , , , ,
2 Comments

I have a couple of interesting pieces coming up.

1.  Mercury Marauder name plate

2.  Closure on the upholstery for my ’70 Mustang.

3.  Reader choice – you choose the next engine to highlight

I have a couple commercial ventures on the near horizon:

1.  Certified Auto Appraiser – I’m about to finish my certification and will be specializing in Classic, Muscle, Antique and speciality cars.

2.  Auto restoration project management.  Focus is on those individuals that love their cars, but don’t have the time nor the experience to know what needs to be done.  I’m actually waiting for my first car.  It is a 1975 VW Bug coming all the way from Iowa City, Iowa, should be here this will for inspection and the beginning of its restoration.

So what engine would you want to see highlighted?  Drop me a note here or on Facebook.

Thanks for reading

 

Wrenchin’ Tip – Got 6 Volts?

By | | , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,
4 Comments

I was recently talking to a coworker of mine who own a 1949 Pontiac Silver Streak Delivery Van (link –     http://wp.me/pKHNM-Bx ) and we were discussing his 6 volt system and the troubles with low amperage.

Well I just ran across a couple of interesting articles dealing with that subject.  Now I will tell you I am not “the guy” for electrical work – nope not me (I had a bad experience – ok – a couple of bad ones).  But even this one I can understand.

Increasing the power supply often means that you need to convert to 12 volt and maybe 15 years ago yes, but now 6 volts are readily available.  So here is what you do (sorry no pics)

Take two 6 volt batters and link them in parallel by connecting the two negative terminals to each other and the two positive to each other. The main positive cable goes from the positive terminal of the first battery to ground and the main negative cable is connected to the negative terminal of the second battery.  Of course in some case you may have to modify the batter shelf, but it will sure help kick up the cold cranking amps.

Thanks for reading

Tim

Car Production Numbers. They Made How Many? 1950

By | | , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,
Leave a comment

Folks seem to like this segment so let’s continue with 1950.

19 major car makers existed back then and Chevy topped the production totals with 1,498,590 units followed closely by Ford with 1, 208,912.  The rest of the field were all less than have that.

Plymouth – 610,954

Buick – 588,439

Pontiac – 466,429

Olds – 408,060

Dodge – 341,797

Studebaker – 320,884  (Don’t ya wish they would have made it?  I would love to have seen their innovation continue.)

Mercury – 293,658

Chrysler – 179,299

Nash – 171,782

DeSoto – 136,203

Hudson – 121,408

Cadillac – 103,857

Packard – 42,627

Lincoln – 28,190

Kaiser – 15,228

Croslely – 6,792

Frazer – 3,700

Of note:

This was the last year for the Old 6 cylinder 76 models, while their Rocket  88 set speed records at Daytona – averaging 100.28 mph.

Packard began selling the only automatic transmission ever developed by an independent car maker.

The Rocket 88 - record setter.

 

Can a pick a Frazer out of a line up?  Me either. Here’s one.

1950 Frazer Manhattan Convertible

How about a Crosley?  Yeah I could do that one.

Crosley Hot Spot - circa 1950

And what did a automatic transmission look like in 1949?  Here is the Packards Ultramatic.

The looked a lot like todays automatic transmissions

 

Thanks for reading.

Tim

Product Review – Griot’s Garage – Long Lasting Tire Dressing Closure

By | | , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,
1 Comment

So you’ve read my review and I promised to drop a note as to the “Long Lasting” part of Griot’s Garage’s – Long Lasting Tire Dressing.

Now is has rained nearly every day since I applied the dressing.

So take a look at the tires with 2 applications and 3 applications.

Tires with 2 applications of tire dressing

 

Here is the tire with 3 applications of tire dressing

 

Here is what I think as a wrap up.   Long lasting to me doesn’t necessarily mean just duration, but can it stand up to everyday driving – oh—yeah…just in case I failed to mention, the  Vette is my daily driver.  It lived up to the Griot promise.  I’ll continue using this product.

Thanks for reading

Tim

 

Tanner 67 Camaro

By | | , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,
1 Comment

A readers’ trip to the drag strip. Tanner Dutton making a pass in his 67 Camaro.  It was an 11.5 pass.  Not too shabby  Tanner.

[vodpod id=Video.13806343&w=425&h=350&fv=%26rel%3D0%26border%3D0%26]

Tanners's Camaro at rest. (That is not Tanner in the pic)