The most American cars on the list are Honda Accord and Element at 80% and 85% respectively, the Ford Explorer at 85% (90% for the 2010 model year) and the Dodge Grand Caravan at 82%.
As I start gathering the different parts for all the new mods for my ’70 Mustang one thing I’m sure of is that I want a little more ‘bling” under the hood. I think the Ford blue engine paint with the brushed nickel look of the current intake need something to offset that color scheme. I’d like to do most of the brackets for the power steering, alternator, and ac compressor all in chrome. However that’s not going to be possible, if I rely on aftermarket/stock suppliers, as most of my brackets are custom-made. (That’s what you get when you keep the 6 cylinder components when you do a conversion to an 8 cylinder.) So I’m going to make do with what I can find and the rest will remain iron.
Now with the cost of all this mods looming on the horizon and having less than the average budget, I’m trying to upgrade at least the tension portions of the Alternator, A/C and the power steering to chrome. My goal is to replace them with heim joints w/adjustable rods between them. These are not inexpensive and often require some modification.
So in the pursuit of this end I purchased a kit from Summit Racing for my alternator. This was an all aluminum kit and only advertised as being for a ‘stock” 302 engine. So going in I knew that it might not work at all. This turned out to be correct except for the heim joints and the threaded aluminum rod.
So I going to use those for the tension rod for the alternator. However, it wasn’t chrome and had a very heavy coding to make it look like brushed nickel. The goal for this pieces was to polish it up and see how “bling” like it could look. This would be a series of repeated sanding, buffing and polishing.
I used my Dremel, sanding disks and buffing and polishing wheel, 200 and 600 grit sand paper and Purple Metal polish, cotton rag (ok..fine it was an old t-shirt) and a vice.
Dremel buffing while and 160 grit sanding disc
Now the 160 grit disk might have been a bit much but the coating was pretty tough and the disc made quick work but did leave a few marks on the test sample that might have causes a bit more work with the lighter grits.
This is actually purple in color and gritty like rubbing compound.
In short the process started with hitting the test piece (one of the stock bracket parts that wouldn’t fit) with the 160 grit disk via the Dremel. Next I ran the 220 grit sandpaper (by hand) over the aluminum and then the 600 grit and then with the buffing/polishing wheel via the Dremel with a coating of the Purple metal polish. I switched it up by using some metal polish with the 600 grit sandpaper.
It took a lot of elbow grease and a couple of hours. Here is what the test piece looks like. You can see the aluminum w/coating and polished portion.
Chrome? Absolutely as shining as chrome.
Now there are some in perfections in the aluminum and if not being careful with the sanding you can leave gouges but generally you can get this type of shine and it looks very close to chrome without the cost, just some elbow grease.
Next will be the polishing of the actual rod that will connect the two heim joints (they are already polished steel). (I’ve already started, but you won’t see it until it complete.)
As I have mentioned, I love the old station wagons. I love the fact that they are being restored. I even like the fact that many are getting the power plants they needed back then transplanted. Although I have to admit I am growing bit tired of the seen a “Corvette” engine between the front wheels – maybe just the fact that they left the “Corvette” labeling on them.
There were some beauties at this show.
All Custom Wagon 1
Nicely Done.
Here is a nicely done Plymouth:
Plymouth Wagon
Love the Nose of this Ply - They really didn't want any one near it.
Now you can call me a DORK but I love this Ford Wagon.
Ford Wagon
Love the Grille
Hey..I even love the hood ornament.
This Torino Wagon, although banged up and hood all mis-aligned, it’s still a keeper with good tread and not too shabbby wheels. I think it’s a keeper.
Ford Torino Wagon.
Lowered but still standing tall was this beautiful Chevy Wagon.
Loving the paint and the roofline!!
I’ve got a few more post coming up shortly before wrapping the Goodguys’ car show trip.
I have a lot more to look at and some senders to chat with. I will wrap this up tomorrow with lot more pics and some commentary.
Thanks for reading.
Tim
Back at the old car corral. My other choice to follow me home. My very first car 1966 Chevy impala complete with nice paint, new top and tired looking but fully complete and running 283! …Yes!!! Bit pricey I thought @ 15k with still a lot of interior work to do.
