If you are over 40, you might remember back when talking to your car was only done to coax it to start or make it to the next service station or when it failed to do either one. Gadgets were limited to a radio with AM/FM and a cigarette liter.
Now days you can give your car voice commands and it can give you a host of information, like my Drivers Information Center (DIC) which runs my C7 Corvette. We can even control the environment on different sides of the car from temperature on down to how much air blows out of your vented seats.
But that wasn’t always the case. If you are way over 30 you might recall the only way to adjust the temperature was to open your vent window.
Recently I was at a car show and if you’re a regular reader you might recall that I love dash boards, especially those that are painted and chromed, I saw a curious feature on a Rambler dashboard(I don’t recall the year). It was labeled “Weather Eye”.
So a little research was in order.
As you may know Nash was an auto maker and through a series of mergers or purchases changed it name to Nash Kalvinater, eventually became American Motors Corporation (AMC). Well they were the first to develop a car heater. Back in 1938 engineers got the idea to run fresh air over the hot engine water and pass it into the cabin. The air came in through the vent in the cowl and passed the air through a heater core filled with hot coolant. Later on they figured out how to keep the warm are in and the cold are out, by adding a fan to keep constant pressure in the cabin.
A year later Nash engineers added a thermostat for the first climate control, dubbed the “The Weather Eye”. Here are some pics:
This was the dash that caught my eye.
Here is an image from the web that shows a better image of the “Weather Eye”
Here is an image show the “Weather Eye’s” controls
A while back I ‘had’ installed a Spec Stage 3 clutch with steel/iron fly-wheel. I did a lot of research before hand and decided that this would be a great combination for my auto cross/daily driver. So far I’ve been happy with the switch. It’s not as ‘street’ smooth as the stock but it helps get the torque to rubber!! But you have to do your research. If you noticed in the first line above I used the phrase ‘had installed’. It is a monster job to disassemble the tunnel and you don’t want to have to do it again after find out that you can’t leave a red like without loosing rubber, nor pay the $$$ for someone else to do it.
I grabbed the article below to share, it has some great tips.
Selecting the Right Clutch for Your C5/C6 Corvette
If you’re a late-model Corvette owner and you’ve ever been in the market for a new clutch, then you’ve discovered that there is such an array of options to choose from, you could find yourself being a little bit lost and confused. To make things even more difficult, thanks to the transaxle layout of the C5 and C6, swapping a clutch is a far more involved process than on a car with a more conventional driveline. A clutch swap isn’t the kind of job you want to do twice on these Corvettes, so getting it right the first time (and having the room to grow for more horsepower and torque down the line) is critical. Read on:
1997-2004 Chevrolet Corvette Clutch Kit Ac Delco Chevrolet Clutch Kit 381408. ac delco clutch press and driven plate kit 11-11/16 in. x 26t x 1-1/8 in. diaphragm; includes flywheel and cover; a high quality direct fit oe …
This is a very well done car, in my opinion. Modified just enough to make it a powerful machine and still look like a 1966 Chevelle. I say ‘WOW” you will too when you read the article. (see the link above)
The Power Plant And Putting It To The Ground
The motor itself is an LS 418 cubic inch stroker with a Lunati crank and H-Beam rods connected to forged pistons. The top end is comprised of ported LS3 heads with an LS9 supercharger. All the machining and assembly of the motor was performed by Scoggin Dickey out of Texas. Mated to the motor is a T-56 six speed transmission that’s outfitted with an ACT dual disc clutch to help lay the power down to the pavement. All this equaled out on the dyno to an impressive 600 hp and 650 lb.-ft. of torque at the wheels.
Monster Chevelle
Got a monster chevy in the garage? Project or not…let me hear about it!!
You will see and enjoy the voices of few very powerful American muscle cars – Mustang Shelby GT500 , Mustang Shelby GT500 Super Snake, Shelby GT & Mustang Shelby KR. Super hot rides, which sound 10 times louder if you hear them live and will make you shake. Anyways check out the video to see this beasts. watch, Enjoy & Share!
While it seems like quite a while since the early December reveal of the 2015 Ford Mustang, the car is very much still in its infancy. Consequently, the most powerful variant currently available is the 5.0-liter V8 powered Mustang GT. However, in the …
If you blinked, you missed it. The limited-edition Mopar ’14 Challenger, the latest Chrysler Group LLC vehicle to come straight from the factory already upgraded with Mopar products, has sold out in just the first day after being made available to dealers.
The Mopar ’14 Challenger is the most recent limited-edition vehicle offered by the brand, continuing the success of the Mopar ’10 Challenger, Mopar ’11 Charger, Mopar ’12 300 and Mopar ’13 Dart in demonstrating how owners can personalize their rides with Mopar products — even before driving away from the dealership. With only 100 built, the Mopar ’14 Challenger is the rarest limited-production Dodge Challenger offered to date.
DETROIT – The all-new 2015 Chevrolet Corvette Z06 is the most capable in the history of the track-oriented model. The Z06 was first offered as an option package in 1963, directed at those who intended to use their Corvettes on a track.
The Z06 since has been offered in four of the Corvette’s seven production generations, each elevating the Corvette’s track capability:
Second generation (1963) – Developed under famed Corvette engineer Zora Arkus-Duntov, the first Z06 package offered enhanced handling and braking capability with an available, larger fuel tank that reduced the need for refueling during a race. Power came from a fuel-injected small block V-8 engine, supported by a four-speed manual transmission and Positraction rear axle. Only 199 were built.
Fifth generation (2001-2004) – Combining a lower curb weight with higher horsepower, the fifth-generation Corvette Z06 was one of the fastest production cars on a track – a capability confirmed with a sub-8-minute lap around the Nürburgring. It was built on a unique fixed-roof hardtop body, with several lightweighting elements, such as thinner glass, a titanium exhaust system and more. Its unique LS6 small block engine delivered up to 405 horsepower through a six-speed manual transmission with specific, performance-optimized gearing. A total of 28,388 were built.
2005 C5 Z06
Sixth generation (2006-2013) – The sixth-generation Corvette Z06 featured its own, bespoke aluminum frame that was 136 pounds lighter than the steel frame on standard Corvette models. Under the hood, the 505-horsepower LS7 7.0L small block featured racing-derived technologies, including titanium connecting rods and a dry-sump oiling system. The Z07 Performance Package added carbon-ceramic matrix brakes and Michelin Pilot Sport Cup tires, enabling the Z06 to run the Nürburgring in 7:22.68. A total of 27,979 were built, including 740 with the Z07 performance package.
2006 C6 Z06 They look soooo good in Black!!!
Seventh generation (2015) – The new 2015 Corvette Z06 is the most capable production Corvette ever. Developed in conjunction with the Corvette C7.R race car, it incorporates racing technology to deliver greater aerodynamic downforce, cornering grip and braking performance. With the available Z07 Performance Package – again fitted with Michelin Pilot Super Sport Cup tires and enhanced braking capability with carbon ceramic-matrix brakes – the new Z06 is faster on a track than the Corvette ZR1, in preliminary testing.
2014 C7 Z06
1963 Z06: Duntov’s legacy
The first Z06 was an option package on the iconic 1963 “split-window” Corvette, developed by Corvette’s legendary engineer and racing advocate Zora Arkus-Duntov. He successfully lobbied for the 1963 Corvette to offer a package for customers who intended to race the new car.
For those in the know, checking the RPO Z06 box on the Corvette’s order sheet added a thicker, 24mm (0.94-inch) front stabilizer bar, larger-diameter shock absorbers and springs that were nearly twice as stiff as standard parts. The Z06 package also featured:
upgraded brake components, including sintered-metal brake linings, which stood up to heat and resisted wear better than conventional material
a dual-circuit master cylinder and vacuum brake booster to enhance safety and reduce braking effort
These components would become industry standards but were still rare in regular-production vehicles of the era.
Possibly most significant for racing, the Z06 option could be combined with a larger, 36.5-gallon fiberglass fuel tank that allowed racers to stay on the track longer. Z06-equipped models quickly became known as “big tank” or “tanker” Corvettes and were originally limited to coupe models because the larger tank wouldn’t fit convertibles. Later, Chevrolet revised the package, making the regular 20-gallon fuel tank standard and the big tank an option. The change allowed the Z06 package to be ordered on a convertible. Only one is believed to have been built. The package originally added more than 40 percent to the Corvette’s base price. Aluminum knock-off wheels were also offered.
There was one engine available with the Z06 package – the 360-horsepower L84-code 327-cubic-inch small block, which featured an advanced mechanical fuel injection system. Corvette was a pioneer in fuel injection, having introduced it in 1957. A four-speed manual transmission and Positraction rear axle were also standard equipment.
In that pre-Internet era, few Corvette customers – even those with racing intentions – knew of the Z06 package. It wasn’t advertised, making word of mouth the primary source of information. Because most were purchased and used for racing, the attrition rate was comparatively high. Remaining, documented examples – especially the big-tank cars – are highly collectable.
2001-2004 Z06: Breaking the 8-minute Nürburgring lap
During the Corvette’s fifth generation, the Z06 name was reintroduced as a special 2001 model that took Corvette performance farther than it had ever been. Engineers started with the Corvette’s unique, limited-production hardtop body, which featured a fixed-roof design that was stiffer and lighter than the hatchback coupe. The car was further lightened with a titanium exhaust system, thinner glass, lighter wheels, conventional tires – in place of the standard run-flat tires – less sound-deadening material, a fixed radio antenna instead of a power antenna, and even a smaller, lighter battery.
The results shaved about 100 pounds off the weight of a conventional coupe model. The car also introduced rear-brake cooling ducts integrated in the rear fenders, which would become a signature styling cue.
On the other side of the power-to-weight equation is horsepower and to that end, the 2001 Z06 used an exclusive LS6 version of the Gen III small block engine. If featured unique internal parts, including a “hotter” camshaft and higher-compression pistons, and an enhanced cylinder block design for greater bay-to-bay breathing, helping it produce 385 horsepower. Further enhancements contributed to an increase to 405 horsepower in 2002. The engine was backed by a six-speed manual transmission with Z06-specific gear ratios.
Like the original 1963 Z06, the fifth-generation car included chassis and suspension components optimized for the track. Its exclusive FE4 suspension package featured larger-diameter, hollow stabilizer bars that also had thicker walls for greater stiffness; larger-diameter shock absorbers compared to standard models, quicker steering – 2.46 turns lock to lock vs. 2.66 on other models – and a larger wheel-and-tire package, featuring Goodyear Eagle F1 SC tires mounted on lighter, stiffer forged aluminum wheels.
By the end of its production run, the fifth-generation-based Corvette Z06 was already benefitting from technology used on the successful Corvette Racing program, including lightweight carbon fiber. A special 2004 24 Hours of Le Mans Commemorative Edition – acknowledging Corvette Racing’s historic 1-2 class finish at the famous 24-hour endurance race – used a carbon fiber hood to shave 10 pounds off the nose of the car, enhancing its balance.
The 2004 Corvette Z06 proved its capability on the global stage, when it became one of the first production cars at the time to run Germany’s famous Nürburgring road course in less than 8 minutes (7:56).
2006-2013 Z06: A foundation for success
The groundbreaking sixth-generation Corvette Z06 elevated Corvette to compete with the world’s most-capable supercars. A power-to-weight ratio of 6.2:1 was one of the best in the world, helping it run from 0 to 60 mph in about 3.7 seconds, through the quarter-mile in the low-11-second range and achieve a top speed of more than 190 mph.
The foundation of the Z06 was its own, dedicated aluminum chassis – the first unique frame for a special model Corvette.
The Z06’s aluminum frame was 136 pounds lighter than the comparable steel frame used in standard models and even incorporated a magnesium engine cradle, contributing to a curb weight of only 3,130 pounds. Mounted on that cradle was another leap in technology: The LS7 small block engine. Displacing 7.0L (427 cubic inches), it was the largest engine offered in the Corvette in more than 30 years – and the most powerful engine in Corvette’s history until the introduction of the Corvette ZR1.
The LS7 used airflow and lightweight technology, including titanium connecting rods and a dry-sump oiling system, derived from the Corvette Racing program to produce 505 horsepower.
Along with its unique frame and LS7 engine, the sixth-generation Corvette Z06 also featured:
More rigid fixed-roof body style
Wider front and rear fenders – including carbon fiber front fenders
Unique rear spoiler and front splitter
Front and rear brake-cooling ducts – including signature integrated rear-fender inlets
Specific, lightweight 18-inch front and 19-inch rear wheels, with 275/35ZR18 front tires and 325/30ZR19 rear tires
Large 14-inch (355 mm) front brake rotors with six-piston calipers and 13.4-inch (340 mm) rear rotors with four-piston calipers
Unique stabilizer bars, spring rates and shocks.
The ultimate Corvette Z06 with the Z07 Performance Package incorporated a number of components used on the 205-mph Corvette ZR1, including carbon ceramic-matrix brake rotors, Michelin Pilot Sport Cup tires, additional carbon fiber exterior components and Magnetic Selective Ride Control. In 2012, a Z07-equipped Corvette lapped the Nürburgring in 7:22.68.
2015 Z06: The most capable ever
The new 2015 Corvette Z06 is the first Z06 to offer a supercharged engine, an automatic transmission and, thanks to a stiffer aluminum frame, a removable roof panel. It is also the most track-capable Corvette, ever.
It was developed in conjunction with the Corvette C7.R race car with technology proven through Corvette Racing, the most successful program in the Tudor United Sports Car Challenge series, formerly the American Le Mans Series.
A new, supercharged 6.2L engine, rated at an estimated 625 horsepower (466 kW), powers the Z06. It is also one of the industry’s only supercars to offer the choice of two transmissions – a seven-speed manual and an all-new eight-speed automatic transmission. Developed by General Motors, the paddle-shift eight-speed offers full manual control, delivering quick, seamless shifts that rival the world’s best dual-clutch/semi-automatic transmissions.
An available, carbon fiber aero package adds a carbon fiber front splitter with aviation-style winglets, carbon fiber rocker panels and a larger rear spoiler with a fixed wickerbill – a small, vertical tab at the edge of the spoiler that significantly increases downforce.
The available Z07 package adds larger winglets, an adjustable, see-through center section on the rear spoiler, Michelin Pilot Super Sport Cup tires and carbon ceramic-matrix brakes. With this package, the Corvette Z06 will deliver the most aerodynamic downforce of any GM production car.
The 2015 Corvette Z06 goes on sale in early 2015.
Founded in 1911 in Detroit, Chevrolet is now one of the world’s largest car brands, doing business in more than 140 countries and selling more than 4.5 million cars and trucks a year. Chevrolet provides customers with fuel-efficient vehicles that feature spirited performance, expressive design, and high quality. More information on Chevrolet models can be found at www.chevrolet.com.
Another week gone and March Madness in upon us. Nope you are going to find any brackets here, just your Auto Factoids for the week.
Big day on the 17th of March. That’s when Geneva attendees were treated to the first of what would become world iconic car. The Porsche debuted back in 1949. Volkswagen or not it is still going strong.
1949 Publicity shot
Although Porsche was in production a few year before this debut. Most of the first Porsche’s contained Volkswagen parts, as the Beetle was the first car the Porsche built.
A few years before the Porsche debut (about 115 – 1834) Gottlieb Daimler was born in Germany on the 17th of March.
Two more March birthdays show up on a search. Those are for Rudolf Diesel in Paris in 1858 and Andy Granatelli in Dallas, TX in 1923, whom just passed way on Dec 29, 2013.
It has long been clear that autism strikes boys more often than girls. But when girls do get the condition, they tend to be at the severely affected end of the spectrum. Now, a group of geneticists thinks they’ve figured out why. Boys, it seems, can …
[ ATTRIBUTE: Please check: http://www.flickr.com/photos/54084461@N07/8689632644 to find out how to attribute this image ]
This a beautiful car, especially if you like station wagons.
These were huge cars. Weighing well over 4K pounds. There were two stations wagons produced that year for Buick the 49 and the 49D. Total production for both was 13,020 units.
The engines in the Buick Special Estate Wagons were a V8 Overhead valve, cast iron block. The power plant displaced 364 cubic inches. The bore was 4.125″ and the stroke was 3.4″ giving the car 9.5:1 compression ratio. Top that will a 2 barrel Stromberg (model 7-106) or a Carter (2529 or 2536 model) carb and it could produce get about 250 hps.
It’s been teased, it’s been partially leaked, but here it is in all its glory: the McLaren 650S. Here’s what you need to know. The 650S is not the long-rumoured ‘baby McLaren’, the car codenamed ‘P13’ set to do battle with the Porsche 911, but rather …
[ ATTRIBUTE: Please check: http://www.flickr.com/photos/54084461@N07/8689632644 to find out how to attribute this image ]
