Category Archives: Auto Restoration

New addition to the C4

By | | , , , , , , , , , , , , , , , , , , , , ,
Leave a comment

It’s been a few days since I posted last, every once in a while life gets a little busy, business travel and a vacation.

However, this blog might have been idle but I wasn’t.

For as long as I’ve owned my vette, I’ve dragged around the original Bose stereo.  Yup, 1980’s technology, with a cassette  and AM and FM radio.  (You kids won’t remmmbbberr….hang on while I put my teeth back in…there…better…remember these and I use to walk to school when I was a kid, up hill both ways and snow up to here!!!!) It sounded really bad.  The cones were mostly dried out from the AZ heat and I think I’ve spent enough on original used speaker and amps (each speaker had its own amp) to buy four stereos with big amps and have the vette vibrate down the street without starting it.  I just didn’t want to get read of the thing….because it was original equipment.

Well, I finally broke down and replaced it.  HOWEVER, not with just a cd player and radio.  Nope.  I wanted something a little more fitting for the car. 

The 1984 C4, as more Corvette peeps know, was the most technologically, advanced car at the time.  It was the first car with computer controlled fuel injection, electronic shifting, and a dash-board with digital and graphic displays….and you can switch it from English to Metric.  So I wanted a stereo, befitting the other technology, but…..say it with me….Average Guy with and Average Budget!!!!!

So I couldn’t go to crazy.  What I did find was an all digital Pioneer Media Center.  No CD.  USB connection for IPODs or just a thump drive.  HD Radio that finds adds all the radio stations and …..wait for it…..drum roll………blue tooth phone connections.  KOOL or what…my wifes’ 08 Lexus has got nothing on my 84 Vette now…..ok..well she does have air-conditioned seats and navigation (…but my phone has that)  and the rear camera and a back seat (over rated!!!) and moon room (but my roof comes off!!)…away there’s more.

I did not want any thing to happen to the original speaker covers nor did I want any new holes, I wanted great sound and an original look.  So I added Alpine SPS 699’s in the rear, 260 watts and 85 RM and Alpine SPS 400 for the door speakers, 140 watts peak and 45 RM.  She sounds great.

 The original Bose system is safe,  all packed and stored.

Thanks for reading.  Drop me a note.

Tim

Auto Factoids for 6/6/2010

By | | , , , , , , , , , , , , , , , , , , ,
Leave a comment

Here ya go:

1928 Plymouth Code Q

7/7/1928 First Plymouth is made, some research suggest that it was actually  built on June 11, 1928.  It had  engineering code (or model) Q and had a 4 cylinder engine.  Check out the video on YouTube. http://www.youtube.com/watch?v=hGfwjTI1ahA

6/10/1951  A Jaguar wins the 24 hours Le Mans – it was a C-type version of XK120.  Here are a couple pics:

Jaguar at a race

XK 120 C

C Type

6/10/1927 – The Graham boys purchased what was Paige_Detroit Motor Cars.  The Grahams started out as farmers and glass bottle makers.  One of  the brothers invented a rear axle that would allow converting Ford car platforms in to light duty trucks.  Oh they are still in business – owning/running Madison Square Gardens and hosting sporting events.

Graham-Paige auto

6/11/1955 Horrific crash at the 24 Hours of Le Mans.  Here are the details from History.com

Prior to the race, Levegh complained that the course was too narrow near the pit-stop area and the grandstand. This observation proved prescient. As Levegh was racing for the lead near the pit-stop area, he swerved to avoid fellow racer Mike Hawthorn s Jaguar as it moved toward the pits. Levegh s car, going about 150 miles per hour, came up too fast on Lance Macklin s Austin-Healey and was catapulted upward. The car crashed into the grandstand and its exploding parts went straight into the crowd. Levegh and more than 80 spectators, packed into the grandstand, lost their lives in the fiery crash.

6/12/1954 – Packard offers the first tubeless tires.

6/12/1975 – The last Chrysler Imperial was made.

1975 4 Door Chrysler Imperial

Thanks for reading.

Tim

Steve Sears 1992 Ford Ranger XLT and Paint

By | | , , , , , , , , , ,
1 Comment

Steve Sears is one of the readers of this blog and owner of a 1982 Mercury Cougar Station Wagon (again..I love this car). 

But that’s not all, Steve does a lot of his own work, including this unique paint job on his 1992 Ranger. 

Here is his recent project. 

The before: 

1992 Ford Ranger XLT

 

Tim, 

  

I completed my project last week and thought you’d like to see it.  I painted my Ranger with a roller.  I only did six coats of each color, usually 8 – 10 coats are required.  I like to call the color Haze gray underway and white.  I spent 26 years in the Navy so I thought the gray was appropriate for me. Ha Ha.  It’s painted with rustoleum mixed with mineral spirits in a 1:1 ratio thus the many coats required.  The body prep is the same as any other type paint job except that a primer is not used over the whole truck.  I only spot primed the bare metal and over the bondo used to fix parking lot dings.  It took a full 8 days to complete the project including the paint on the topper.  I have to wait a few weeks before buffing out for a full gloss.  For that I’ll just remove the mirrors and the bug shield on the front.  The process is well documented on the web over the last 10 years or so so I won’t repeat the process.   

  

I thought your readers would be interested. Finally I have the truck looking like new again.  It’s a 1992 Ranger XLT that I had bought new on April 24, 1992.  It has the 2.3 liter four and a five speed tranny.  The picture labeled 019.JPG is the before shot is attached.  

And the after photos: 

After Pic 1

  

After Pic 2

  

After Pic 3

Thanks very much for sharing it Steve.  (A roller?  Wow!!!!)  

  Drop me your comments!!!! 

Thanks for reading 

Tim 

Auto Factoids for the Week of 5/30/2010

By | | , , , , , , , , , , , , , , , , , , , , ,
3 Comments

5/31/1927 – Mr. Ford produces the last Model T

6/2/1899 – Locomobile Co. Founded – they were in business until 1929.  They made a lot of cars, I hadn’t realized that.  Here are a couple.

1901 Locomobille - Cool..wonder what the 1/4 mile time were??

Love this one..Steam powered????

1923 48 Series Sport

6/3/1864 Ransom Olds was born in Ohio.  He developed and build cars named after him,  Oldsmobile and REO (his middle name was Eli, hence REO, hey that was a band name REO Speedwagon.

An Reo Speedwagon

I’ve never heard of the next guy, until now and did a little reading.

Barney Oldfield was born 6/3/1878.  He was a race car drive, but started out racing bike and wining silver medals in the process.  Here are a couple pics:

Early 1900's

Oh Yeah..that Henry Ford standing next to his car.

Bowling Green Corvette Assembly Plant Tour…AWESOME!!

By | | , , , , , , , , , , , , , , , , , , , ,
3 Comments

I attended the Bowling Green Assembly Plant tour today.  It was really!!!!! awesome!!!!!

Corvette Assembly Plant Bowling Green, KY

 

The walk from the parking lot to the plant was filled with the smell of new car.  They must pour it out of every chimney and window.

They were building the Z06’s, ZR1 and Grand Sports…a lot of Grand Sports!!! (that is a damn nice car!!!) Amazing!!!!    Sorry no pictures were allowed.

Seeing all the parts everywhere and the hanging panels and frames…was a sight to be hold.

The tour was pretty quick..well maybe an hour…but I could have hung there all day!!!  I lagged behind the tour group and spoke with a couple of the workers.

At one stop, where they fill the newly married body, chassy and engine with fluid, the tour guide was going blah, blah, blah and I was looking over the cars and one of the guys walked over asked me if I had one picked out yet.  He said they seemed to be selling a lot of GS’s.  I asked him about the fender stripes and he said they normally just get tossed in the back and the dealership installs them.  He asked me if I liked the wider body and I said what’s not to like!!!!

We watched them marry up a Zo6’s mufflers, while another guy stuck in the tail lights and then on to the chassy.  Tire position was at a stop.

Actually got to watch a new Grand Sport come off the line and run over the ‘suspension’ activation section (floor) and then into the section where they align the headlights.

We  got to see a Z06 enter the final test chamber where they run 200 + tests in two minutes.  This one passed.

It was MOST EXCELLENT!!!! (Wayne’s World).

The NCM was good, but the plant tour overshadowed it…by far.   I’ll post up pics from the  NCM in the next post.

corvettte assembly plant

Auto Factoids for Week of 5/23/2010

By | | , , , , , , , , , , , , , , , , , , , ,
Leave a comment

Few major milestones this week. 

Brooklyn bridge opened for traffic on 5/24 1883 and the Golden opened 5/27 in 1937. 

Race car driver Mauri Rose was born 5/26/1906 currently in the racing hall of fame, placed second in the 1927 Indy 500.  Actually won the Indy in 1941, but that was a tough victory, spanning two Maserati-powered Elgin Piston Pin Specials cars, after the first one had mechanical issues.  He tossed a fit and the car owners pulled one of the other drivers on the time from the race and give Rose that car. 

The Pin 

Elgin Pin

 

What powered that thing? 

Power Plant

 

The first Kaiser-Frazer was produced 5/28/1946 – cars weren’t sold until 1947. 

1947 Willow Run Plant

Mustang Hose Woes – The Cause of it all.

By | | , , , , , , , ,
1 Comment

Sometimes old car parts break…that’s the nature of things old.  However, most of my Mustang’s parts are only 3 years old or so. 

So sometimes new parts break when they are used in a restoration along with existing older parts.  This was the case with the power steering hose failure. 

If you haven’t read my entire 130 posts thus far (why not???…toe tapping…toe tapping), you might not have picked up on the fact that my 70 coupe started out life with a 9.1:1 compression 250 straight 6 “power plant”. Now it’s a fire-breathing 302…ok…no fire..but a 302 none the less. 

I won’t go to all the trial and tribulations of the 6 to V8 conversion..right now..but soon, but here it’s necessary to share what I know.  It is not an uncommon practice to be swap out a 6 cylinder for more power.  You can quite often, pick up a 6 banger cheaper, than an a v8.  Just as often difficulties arise in the course of the improvement. eerrrkkkk…There are some people who believe it was blasphemy replacing the 250 – there weren’t that many made that year. There is a small group of guys that were a bit dismayed when I didn’t keep the 6. (I am too..now.)  That group has done some amazing things with a 6 cylinder, that make my 302 ‘Stang look like a pedal car!!  I have their book so some, I’ll post up the details when I get back in town….End of eeerrrrkk 

After looking at the broken hose, which was bent and cracked near the flared end. 

Power Steering break point

 

Here is what I learned.  The 1970 coupe 6 cylinder has a different power steering package then does the 8 cylinder.  Specifically, the difference is the way the power steering pump is mounted and the length of the hose.  I recall when the part was getting installed, I was called to determine how we wanted to proceed when it was noticed that the hose, in order to reach the new height of the pump, could possibly come in continued contact with the control arms. This would cause a  rubbing between the two pieces against the rubber portion of the hose.  The decision was made to double the hose – by cutting a larger hose and enclosing the original in side and using ties to secure it. 

This worked just fine while the front end stayed …well old and sloppy.  Just recently I posted about replacing the upper control arms and in doing so, tightening up the front end and removing the slop that allowed the clearance to be  greater between the two parts.  With less space between them, the control arm came into contact with the hose and after several bumps getting in an out of my driveway the hose got crimped and then broke. 

Ordered another hose for a V8 and had it installed.  Everything functioning properly. 

Thanks reading. 

Tim

Mustang Hose Woes

By | | , , , , , , , , , , , , , , , , , , ,
4 Comments

I was about to start the pillar moldings mini project when I ran into a couple mechanical issues.

About a week ago the Mustang began squealing when pushed to high revs.  That normally indicates one of several problems.

1. It could be a water pump

2.  It could be the power steering pump

3.  It could be a pulley

4. It could be a bolt that was holding the alternator bracket to the engine worked itself out and was in contact with the fan belt.

5. It could be a combination of the any of these.

Now the Mustang did, every once in a while, drip some fluid from the power steering control value but it wasn’t a huge deal.

Well, Saturday I went to start her and the battery was dead.  It’s over 3 years old and I had left the lights on the day before and had to have it jump started.  So off to the auto parts store I went and pick up a new 3 year battery and stuck it. When I started the engine up, it made the squeal and I decided I needed to fix this, before the pillar molding.

So with a neighbor revving the engine I noticed the bolt protruding from the water pump/block ( it passes through left side water pump housing in to the block).  With the revs the fan belt would flex and briefly hit the bolt.   This bolt was “custom” made when we were fitting everything up to reman’ed long block and was about 7 or 8 inches long.

It took a bit to get that back in place, had to loosen up the alternator’s other two supports and toss a little loctite on the threads and she was good to go…..almost…..

Yeah….option #5 above was the correct answer BTW.

Started it up and there was still a squeal – not the same squeal but clearly an ‘accompaning’ squeal.  Shortly after that a power steering hose let go and well liquid does what gravity  make it do and I spent the afternoon cleaning the driveway.  So there went my allotted time for Saturday.   So replacing both hoses seem the best way to go and they’ll  be in today.  Right now it’s at the shop down the street, I had no time to undertake this task at the moment, will be traveling the next couple weeks.

One of my travels takes me to the National Corvette Museum.  I’ll spend an entire day there which include the assembly plant tour.

Thanks for reading.

Tim

Auto Factoids for 5/9/2010

By | | , , , , , , ,
1 Comment

Tough finding something historic for this week in May.

I do have a blurb on GM.

On May 10, 1923 they named Alfred P. Sloan as corporate president.  They didn’t just pick from the streets.  He was actually, a draftsman for a bearing company, Hyatt Roller Bearing.  That company eventually merged with a few other companies with United Motor Corporation.  Sloan became the president of that and shortly after that they were purchased by GM.

He served GM from 1923 to 1956 in some manner including board chairman.

Thanks for reading.

Tim

V8 Reference Book

By | | , , , , , , , , , , , , , , , , , , ,
Leave a comment

I grab every book I think is useful in any of my hobbies.  I happened to be at the mall the other day and had some time kill and wonder down to Borders books store.  Pick up a book entitled “Ultimate American V-8 Engine Data Book” 2 Edition  by Peter Sessler, published MotorBooks.

This book has engine identification codes, component casting codes, internal dimensions and specs, and power and torque ratings.

It goes back as far as 1952 and covers Fords, GM, Mopar, and AMC, Packard and Studebaker.  It includes big blocks and small blocks.  There is a lot of information.

I learned from this book that all of the engines possible for the Corvette in 1984 were rated @ 205 hp.  The CFI was the main power supplier, but it also had listed a couple TPI’s (engine suffix code ZFC), TBI (engine suffix code ZFJ – supposedly for export only) and a 4v for California (engine suffix code ZFF).

They also inform you of the transmissions that go with the engines.

There are listings for cylinder heads parts or casting # as well as intake and exhaust manifolds as well.

I think this one is worth the  $30.00.

This is a great transition to introduce an up and coming feature for this blog.

I love engines…(duh).  To me the history of development, what was used when and where and maybe even why can be fascinating.  I’ll be tossing out specs and the like and hopefully some, ” I would have never guessed that” information.  Now, I don’t have this all in my head, it will be researched stuff or some experiences. (My 1974 Torino was a good case study..tell you the story soon).

Thanks for reading.

Tim